还剩7页未读,继续阅读
文本内容:
冬期施工监理控制要点
一、工程概况北京地铁6号线东小营车辆段,出入段线自接轨站引出向东南方向进入车辆段段内线路沿东侧的减运河布置,由东向西横向排列依次为试车线、停车列检库、清扫库、月修库、静调库、架修库其中清扫库、月修库、静调库和架修库合并布置,这种布置使土地利用率高、工艺流程顺畅、主次分明、场内作业简单快捷,既满足规划要求,且有利于远期发展
二、本项目冬期施工的特点本项目地处北京市通州区,地理纬度高,冬季时间长由于工期时间较紧,项目必须在较严寒的冬季进行施工由于项目规模大,所需施工工期长,受冬季影响的冬期施工分项工程主要有钢筋工程、混凝土工程、土方工程、安装设备工程等根据北京市的气温特点平均气温低于5°C的起止时间为每年11月至次年的3月但根据历年气温的变化规律,冬期施工又可分为一般低温阶段和极低温阶段极低温阶段的时间是每年的12月下旬至次年的1月下旬,日最低气温大约在-10°C•左右,在此期间拌合料所用的水、砂子必须加热,并掺砼防冻剂进行施工,砼浇筑后用塑料膜及草袋覆盖保温
三、编制依据
1.监理合同(包含正式文件、修正或补充文件);
2.施工图纸及说明;
3.设计、技术规范、工程质量检验评定标准、试验规程等;
4.国家监理法规、规定等;
5.《建筑工程冬季施工规程》JGJ104-2011
四、冬期施工时段规范规定室外日平均气温连续5天低于5℃即进入冬期施工,室外日平均气温连续5天稳定高于5℃即结束冬期施工
五、监理工作流程
1.施工前
2.施工中
3.冬期施工后及时做好对冬期施工资料整理
4.主体结构钢筋混凝土工程质量控制监理工作流程
六、监理控制原则结合施工单位提交的冬期施工的施工方案对用于工程的各种材料、机械设备进行检查对工程拟采用的实验室及试验设备进行复核等事前控制措施我监理部及时召开冬季施工专题会议并事前做到:
1.及时确定冬施开始时间下发关于针对本工程冬季施工的人员、材料、机械等安全注意事项的通知确保从意识上灌输给施工队安全为天的施工理念并要求其项目部积极组织安全培训教育保证工程施工中减少事故隐患监理部随时检查;
2.要求施工方落实冬施施工方案中保温材料等冬施物资配备例如棉被、草帘子等覆盖用品对施工过程的质量控制采取“安全为天质量第一”的原则按照合同文件规定的设计图纸质量检验评定标准施工技术规范和试验检测规程等的要求进行质量控制1对影响工程质量的重点和难点环节明确工地现场责任人、明确组织、落实措施2对工程项目实施全过程、全方位的质量控制不放过任何环节3不合格的材料不得使用;不合格的工艺不得实施;不合格的工程不得验收签认4严格监理程序尤其是审批程序验收程序和事故处理程序5质量控制方法采用:预防、旁站、巡视、现场检验、测量、监理指令等方法6监理进度控制的总原则是总体安排、阶段控制、分项管理、月度统计分析对应到进度计划上分别为总体工程进度计划、阶段工程进度计划、分项工程进度计划和月进度计划7监理对进度控制的目标应符合合同文件所规定的工期目标8监理对进度控制应在确保工程质量与安全的前提下进行9监理应及时掌握工程进度信息并进行统计分析做到主动控制10通过监督承包人按时提交进度计划并严格审批来体现监理对工程进度的领先控制
七、冬期施工前的准备工作
1.成立冬施领导小组组长李炜组员程安春、白殿涛、门新哲、白变霞、付迪
2.技术准备冬施前,要求施工单位对测温人员、混凝土试块制作人员、安全防火人员以及技术管理人员都要进行技术培训后上岗各单位都必须指定专人负责测温工作,对现场施工人员进行冬期施工技术交底,掌握冬期施工控制要点对本工程冬期施工项目进行确定,明确责任工程技术人员和项目管理人员必须认真复核图纸,查对是否能适应冬期施工的要求施工现场设测温箱,安排专人测量施工期间的室外气温,混凝土来料、入模、后期强度增长的温度并做好记录每天查看当地天气预报,掌握天气变化情况,防止寒流的突然袭击
3.材料准备督促施工单位提前做好冬期施工的各种材料、外加剂的准备工作(其中包括保温材料),提前与商品混凝土厂家取得联系,做好试配工作,并提供施工配合比a加强对搅拌站的保温防护,上、下水管道的检修、防护,在11月15号前应全部做好b加强锅炉房等供暖设备的维修保养工作,确保正常供暖,供暖管沟要进行一次彻底的检查,排除隐患另外,要注意供暖燃料的储备c提早准备冬期施工的原材料,尤其要提前预备3个月的砼用砂,以防冬季购砂困难或临时购砂因含水过多而结成冰块,无法使用冬季用外加剂(早强剂、防冻剂)要及早与厂家联系,按照规范要求安排试验复试,确保冬季施工外加剂的质量与数量d冬季施工前组织有关人员学习冬季施工技术规程,提前做好防冻剂必试项目试验,完成冬季常用砼配合比的设计
八、砼冬期施工的一般原理砼拌合物浇灌后之所以能逐渐凝结和硬化,直接获得最终强度,是由于水泥水化作用的结果而水泥水化作用的速度除了与砼本身组成材料和配合比有关外,主要是随着温度的高低而变化的当温度升高时,水化作用加快,强度增长也较快;而当温度低于0℃时,存在于混凝土中的一部分水分开始结冰,逐渐由液相(水)变为固相(水)这是参与水泥水化的水少了,因此,水化作用减慢,强度增长相应较慢,温度继续下降,当存在于混凝土中的水完全变成冰时,水泥水化作用基本停止,此时强度不在增长水变成冰时,体积约增大9%,同时产生约2500kg/cm3的冰涨应力,这个值通常大于水泥石内部形成的初期强度值,使混凝土收到不同程度的破坏(即早期受冻破坏)而降低强度此外,当水变成冰时,还会在骨料和钢筋表面产生颗粒较大的冰凌,减弱水泥浆与骨料钢筋的粘结力,从而影响混凝土的抗压强度,当冰凌融化后,又会在混凝土内部产生各种各样的空隙,而降低混凝土的密实性和耐久性由此可见,在冬季混凝土施工中,水的形态变化是影响混凝土强度的关键新浇混凝土在冻结前有一段预养期,可以增加其内部液相,减少固相,加速水泥的水化作用混凝土受冻前预养期越长,强度损失越小混凝土化冻后(即处在正常温度条件下)继续养护,期强度还会增长,不过增长的幅度大小不一对于预养期长,获得初期强度较强(如达到R28的35%)的混凝土受冻后,后期强度几乎没有损失对于安全预养期短,获得初期强度较低的混凝土受冻后,后期强度都有不同程度的损失因此,在混凝土受冻前,要使其在正常温度下有一段预养期,以加快水泥的水化作用,是混凝土获得不受冻害的最低强度,一般称临界强度,即可到达预期效果对于临界强度,我国规定不低于设计强度的30%,也不低于35kg/cm3
九、混凝土冬季施工方法的选择从以上分析可以看出,在冬季砼施工中,主要解决三个问题,一是如何确定砼最短的养护龄期,二是如何防止砼早期冻害,三是如何保证混凝土后期强度和耐久性满足要求在实际工程中,要根据施工时的实际气温情况,工程机构状况(工程量、结构厚大程度与外露情况),工期紧迫程度,水泥的品种及价格,早强剂、减水剂、抗冻剂的性能及价格,保温材料的性能及价格,热源条件等,来选择适合理的施工方法一般来说,对于同一个工程,可以有不同的几个冬季施工,来获得最优良的工程质量,也就是工期、质量、费用最佳化目前,基本使用一下四种方法
1、调整配合比法主要用于0℃左右的砼施工具体做法
①选择适当品种的水泥是提高砼抗冻的重要手段试验结果表明,应使用早强硅酸盐水泥该水泥水化热较大,且在早期放出强度最高,一般三天抗压强度大约相当于普通硅酸盐水泥7天的强度,效果比较明显
②尽量降低水灰比,少增加水泥用量,从而增加水化热量,缩短达到龄期强度的时间
③掺用引气剂,在保持混凝土配合比不变的情况下,加入引气剂后产生的气泡,相应增加了水泥浆的体积,提高拌合物的流动性
④掺加早强外加剂,缩短混凝土的凝结时间,提高早期强度应用较普遍的有硫酸钠(掺和水泥用量的2%)和MS-F复合早强试水剂(水泥用量的5%)
⑤选择颗粒硬度高和缝隙少的集料,时期热膨胀系数和周围砂浆的膨胀系数相近
2、蓄热法只要用于气温在-10℃左右,结构比较厚大的工程做法是对原材料(水、砂、石)进行加热,使混凝土在搅拌、运输和浇灌以后,还储备有相当的热量,以使水泥水化放热较快,并加强砼的保温,以保证温度在下降到0℃以前,使新浇混凝土具有足够的抗冻能力此法工艺简单,施工费用不多,但要注意内部保温,便面角部和外露受冻,且要延长养护龄期
3、外部加热法只要用于-10℃以上,而构件并不大厚的工程通过加热砼周围环境的空气,将热量传给砼,或直接给砼加热,使砼处于正温环境下能正常硬化
①火炉加热一般在较小的工地使用,方法简单,但室内温度不高,比较干燥,且放出的二氧化碳会使新浇混凝土表面碳化,影响质量
②蒸汽加热用蒸汽使混凝土在湿热条件下硬化此法较易控制,加热温度均匀但其需要专门的锅炉设备,费用较高且热量损失较大,劳动条件亦不理想
③电加热将钢筋作为电极,或将电热器贴在混凝土表面,变电能为热能,以提高混凝土的温度此法简单方便,热损失较少,易控制,不足之处是电能消耗量大
④红外线加热以高温电加热器或气体红外线发生器,对混凝土进行密封辐射加热
4、抗冻外加剂在-10℃以上的气温中,对混凝土拌合物掺加一种能降低水的冰点的化学剂,使混凝土在负温下仍处于液相状态,水化作用能继续进行,从而使砼强度继续增长抗冻剂必须经环保部门的认证,不含氨、氡等对人体有害的物质目前常用的有氧化钙、氯化钠等的抗冻剂及亚硝酸钠加氯化钠复合抗冻剂上述四种冬季施工方法都有利有弊,其使用范围都受一定条件制约应根据工地现有条件,采用一种或两种以上施工方法结合使用
十、冬期施工各阶段监理控制要点一施工前的准备阶段控制
1.冬季施工方案审核及落实情况
2.冬季施工材料准备情况,如防寒、加热、测温仪等二冬季施工材料控制
1.外加剂使用情况以及材料的详细说明和相关有效证明文件,必须满足冬季施工规范要求,否则将不得在本工程中使用
2.对于进场的沙子应严格控制冻块,施工用水温度必须符合规范规定,并做好
3.不定时对混凝土搅拌站的材料特别是砂、石子、水的使用情况是否满足冬期施工要求进行控制
4.严格控制混凝土的出模温度并按规范要求做好记录三各分部工程冬季施工过程控制
1.模板工程1模板上不得存有冰雪及积水,墙及柱内如有积雪必须清理和扫除干净后方可施工2竖向支撑体系必须稳定,牢固,不得支撑在冰块上3根据冬期气温下降程度,当不能满足东施要求时,模板外挂一层阻燃保温棉毡进行保温
2.钢筋工程1如在施工过程出现突发天气(下雪)必须及时将钢筋上的积雪清除干净方可进入下边工序施工2钢筋调直冷拉温度不宜低于-20℃3钢筋负温焊接,可采用闪光对焊、电弧焊、电渣压力焊等方法当环境温度低于-20℃时,不宜进行施焊4负温条件下使用的钢筋,施工过程中应加强管理和检验,钢筋在运输和加工过程中应防止撞击和刻痕5钢筋张拉与冷拉设备、仪表和液压工作系统油液应根据环境温度选用,并应在使用温度条件下进行配套校验6当环境温度低于-20℃时,不得对HRB
335、HRB400钢筋进行冷弯加工7雪天或施焊现场风速超过三级风焊接时,应采取遮蔽措施,焊接后未冷却的接头应避免碰到冰雪8钢筋负温电弧焊宜采取分层控温施焊热轧钢筋焊接的层间温度宜控制在150℃一350℃之间9钢筋负温电弧焊可根据钢筋牌号、直径、接头形式和焊接位置选择焊条和焊接电流焊接时应采取防止产生过热、烧伤、咬肉和裂缝等措施
3.混凝土工程1混凝土工程的冬季施工,除按常温施工的要求进行质量检查外,尚应检查以下项目a拌制混凝土所用的砂石骨料应清洁,不得含有冰、雪、冻块及其它易裂物质,各种材料的含碱量应根据砼所用部位和所处环境的不同,符合规范要求b冬施所用的防冻剂、外加剂要有市建委颁发的使用准用证,出厂合格证及产品说明书,并且经过复试及实际考察合格后才能使用c为了保证冬施混凝土温度,应该对水、砂、石通过蒸汽分别进行加热优先采用加热水的方法,当加热水仍满足不了要求时,再对骨料进行加热水、骨料加热的最高温度应符合下表的规定当水、骨料达到规定的温度仍不能满足热工计算要求时,可提高水温到100℃但应改变投料顺序水泥不能与80℃以上的水直接接触拌制砼时搅拌机投料顺序应先下砂、石、水搅拌后再下水泥搅拌,搅拌时间比正常季节延长50s砼出机温度不低于20℃,砼入仓温度不低于10℃,入模温度不低于5℃拌合水及骨料加热最高温度d要加强对砂、石、水、水泥的温度测量并做好记录,做好对砼试块的保管养护e运输搅拌罐车上覆盖好保温套并做好保温工作,减少砼热量的损失f做好搅拌机室和后台料仓的保温工作,温度控制在15~20℃,减少砼拌合过程中热量的损失g要合理安排生产,防止砼在工地停滞时间过长而造成热量损失,导致砼入模温度低于5℃或早期受冻2水、骨料及混凝土出机时的温度,每工作班至少测量4次3混凝土温度的测量a采用蓄热法养护混凝土时,养护期间每昼夜测量4次b负温混凝土,强度达到抗冻临界温度以前,每隔2h测量1次,以后每昼夜测量2次c室外空气温度及周围环境温度,每昼夜测量4次4混凝土的温度测量,应按下列规定进行a全部测温孔、点均应编号,编制布置图,测量结果要写入正式记录b测温孔、点应设在有代表性的结构部位和温度变化大,易冷却部位,测温孔的深度一般为10—15cm,或板、墙厚度的一半c测温时,应将温度计与外界气温做妥善隔离,可在孔口四周用保温材料塞住,温度计在测温孔内应留置3min以上,方可读数5测量读数时,应使视线和温度计的水银柱顶点保持在同一水平高度上,以避免视差,读数时,要迅速准确,勿使头,手或灯头接近温度计下端,找到温度计水银柱顶点后,先读小数,后读大数,记录后再复验一次,以免误读6测温人员应同时检查覆盖保温情况,并应了解结构物的浇筑日期,要求温度,养护期限等若发现混凝土温度有过高或过低现象,应立即通知有关人员,及时采取有效措施7在混凝土施工过程中,要在浇筑地点随机取样制作试件,每次取样应同时制作6组试件试块留置具体如下a标养28d试块留置b用于拆模依据的同条件试块c用于检测临界强度的同条件试块关于临界强度的说法为《建筑工程冬期施工规程》中
7.
1.1冬期浇筑的混凝土其受冻临界强度应符合下列规定
①普通混凝土采用硅酸盐水泥或普通硅酸盐水泥配制时应为设计的混凝土强度标准值的30%,采用矿渣硅酸盐水泥配制的混凝土应为设计的混凝土强度标准值的40%
②掺用防冻剂的混凝土当室外最低气温不低于-15℃时不得小于
4.0N/mm2,当室外最低气温不低于-30℃时不得小
5.0N/mm2d负温转常温的同条件试块冬季施工同条件下养护到明年常温状态下28d的强度测试e用于结构验收的同条件试块即600℃.d的试块,600℃.d的计算要确保准确,具体计算为从试块留置那天算起每天的平均气温的累加到600就可以,但总天数不应少于14天,不宜大于60天,且最重要的是每天气温里的负温不计算,从正温到零累加在平均,如今天气温是最高6℃,最低-3℃,那平均气温为(6+0)/2=3f备用的同条件试块
十一、机械设备冬期防寒、防冻、防火、防滑工作措施
1.在进入冬期前对所有机械设备做全面的维修和保养,作好油水管理工作,结合机械设备的换季保养,及时更换相应牌号的润滑油;对使用防冻液的机械设备确保防冻液符合当地防冻要求;未使用防冻液的机械设备要采取相应的防冻措施(采取停机后排放冷却水或进入暖棚车间内)
2.各种车辆使用的燃油,要根据环境气温选择相应的型号,冷车起步时,要先低速运行一段路程后再逐步提高车速
3.冬期车辆启动发动机前,严禁用明火对既有燃油系统进行淤热,以防止发生火灾
4.冰雪天行车,汽车要设置防滑链;司机在出车前检查确认车辆的制动装置是否达到良好状态,不满足要求时不得出车,遇有六级以上大风、大雪大雾不良气候时停止运行
5.严格执行定机定人制度,机械保管人员要坚守岗位,看管好设备,并作好相应的记录严格执行派车单作业票制度
十二、冬期施工安全教育及培训冬期施工应遵守安全法规和规程
1.对全体职工定期进行技术安全教育,结合工程任务在冬施前做好安全技术交底,配备好安全防护用品
2.由安全员对工人必须进行安全教育和操作规程的培训,对变换工种及临时参加生产劳动的人中,也要进行安全教育和安全交底
3.特殊工种(包括电气、架子、起重、锅炉、焊接、机械、车辆等工种)须经有关部门专业培训,持有上岗证后方可操作
4.所有工种的都必须有安全员的详细安全措施交底,否则不许施工
十三、冬期施工安全管理措施
1.施工现场管理1)现场内的各种材料、半成品、砼构件、乙炔瓶、氧气等存放场地都要符合安全要求,并加强管理2)加强季节性劳动保护工作霜雪天后要及时清扫大风雪后及时检查脚手架,防止高空坠落事故发生,并应保证消防道路畅通3)将现场的积水或积雪应及时清理干净,不应使场地造成积水现象而导致因温度过低时而结冰,造成安全隐患4)在砼浇灌前应提前进行模板钢筋和预、埋件检查,清理梁、板内积雪,冰块,使用的脚手架、马道应保证使用安全,搭设人行走处均应铺设为竹架板或木版,并不应有积冰雪,防止滑动伤人,在重要部位铺设干草草帘防滑
2.冬期电气安全管理1)在冬期施工防案和施工组织时间中,必须有现场电器线路及施工位置平面图现场应设电工负责安装、维护和管理用电设备,严禁非电工人员随意拆改2)施工现场严禁使用裸线电线铺设要防砸、防碾压,防止电线冻结在冰雪之中大风雪后,应对供电线路进行检查,防止断线造成触电事故3)用电设备采用专用电闸箱强电源与弱电源的插销要区分开,防止误操作造成事故
3.解除冬期施工后的安全管理随着气温的回升,连续七昼夜不出现负温度方可解除冬施但注意以下几点1)冬期施工搭设的超过三层楼以上的架子,塔式起重视路基和电线杆等,应进行一次普查,防止地基浆融沉陷造成倾斜倒塌2)材料堆放场、大模板堆放场应进行检查和整理防止垛堆、没半和构件在土层冻融中倒塌。