还剩64页未读,继续阅读
本资源只提供10页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
文本内容:
厦门海洋职业技术学院毕业设计(论文)题目:网络综合布线系统设计系别信息技术系班级通信3102姓名李艺彬学号1002302095指导教师陈志贵2013年3月25日编号XH03JW037-09/0厦门海洋职业技术学院毕业设计(论文)任务书课题名称网络综合布线设计系别信息技术系专业通信技术教研室通信教研室指导教师陈志贵学生姓名李艺彬学号1002302095二○一二年12月30日设计(论文)内容
1.确定工程实施的范围;现场勘察,了解并记录建筑物情况;
2.确定系统各类信息点接入要求;确定建筑物合适的FD-BD结构;
3.确定综合布线总体设备配置,绘制企业网络综合布线系统结构图;
4.编制楼宇建筑综合布线设计方案;
5.编制中心机房设计方案,确定机房中选用的各项材料;
6.编制综合布线施工方案及其注意事项设计(论文)的主要技术指标综合布线是一种模块化的、灵活性极高的建筑物内或建筑群之间的信息传输通道它既能使语音、数据、图像设备和交换设备与其它信息管理系统彼此相连也能使这些设备与外部相连接它能够同时提供语音、数据和视频传输实现信息资源共享本设计在遵循设计基本原则的基础上经过对长通院新建综合楼的勘察以满足综合楼与学校实现信息资源共享的需求设计了符合要求的各个子系统选择先进、高品质的综合布线产品以高的性能指标、好的工艺性能确保综合布线系统能够满足智能化系统应用的要求使用光纤作为系统主干冗余配置提高系统宽带并防止电磁干扰适应未来发展主干光缆可支持1Gbps以上的网络数据传输速率水平超5类电缆可支持100Mbps以上的网络数据传输速率星型的拓扑结构支持各种形式的网络应用为综合楼提供全方位的应用平台支持办公网络设备、各种采编设备及保安设备等的系统集成以机柜型配线系统为核心努力提高系统的可靠性和安全性具有开放式的结构能与众多厂家的产品兼容具有模块化、可扩展、面向用户的特点能完全满足现在以及今后在语音、数据及影像通信方面的需求能将语音、数据与影像等方面的通信融于一体可应用于各种局域网络LAN能适应将来网络结构的更改或设备的扩充本系统能实现电话通信、计算机网络、BAS、CAS、OAS、SCS等系统网络集成、、视频传输及其他符合布线标准的信号、数据传输本系统服务效在率、服务质量、网络吞吐率、网络响应时间、数据传输速度、资源利用率、可靠性、性能/价格比等性能需求上均达到
三、具体要求
1.准备阶段(12月15日—12月18日)对教学楼2号楼和公寓楼3号楼进行现场勘查,了解记录楼宇的楼层数、房间数、面积、结构、用途等信息;收集关于综合布线网络设计的原则、规范、标准、选材、施工注意事项等相关资料;对调查和收集的信息进行整理
2.初期设计阶段(12月19日—12月22日)根据调查和收集的信息,列出大概的设计纲要,主要分成四个部分,包括网络综合布线系统的概述、教学楼、公寓楼网络综合布线需求分析、编制楼宇建筑综合布线设计方案、综合布线施工方案
3.具体设计阶段(12月23日—1月7日)对初期的设计纲要进行深入详细的分析、设计,列出每部分的具体设计原则和规范;根据这些原则规范设计合理的方案,将方案描写具体清楚完整;按照设计的方案画出设计图纸
4.检查修改阶段(1月8日—1月15日)设计完成之后,检查方案有没有错误的地方,进行修改;根据总体的设计方案,修改设计上一些不足或者遗漏的地方,使方案更完美
四、主要参考文献的范围
[1]刘省贤•综合布线技术教程与实训•北京大学出版社•2006年
[2]余明辉•综合布线系统的设计施工测试验收与维护•人民邮电出版社•2011年
[3]《建筑与建筑群综合布线系统工程设计规范》(GB/T50311-2007)
[4]《建筑与建筑群综合布线系统工程设计规范》(GB/T50311-2007)
[5]黎连业•综合布线系统与施工技术•高等教育出版社•2002年
[6]福禄克网络学院•布线系统测试工程师认证培训教程•2009年
[7]安顺合•智能建筑施工与验收手册•中国建筑工业出版社•2006年
[8]雷锐生•综合布线系统方案设计•西安电子科技大学出版社•2004年
[9]信息产业部•综合布线工程验收规范(GB50312——2007)•中国计划出版社•2007
[10]信息产业部•《GB50314——2007智能建筑设计规范》•中国建筑科技出版社出版•2007年
五、其他需要说明的事项无毕业设计(论文)开题报告表编号XH03JW037-10/0系:信息技术系专业:通信技术班级:3102学生姓名李艺彬学号1002302095指导教师陈志贵课题名称网络综合布线系统设计
一、课题概况(本课题的意义及目前的发展状况等)本次设计的对象是厦门海洋职业学院宿舍楼3号楼与教学楼2号楼,占地面积大概600平方米左右,楼宇间的通信非常重要,网络综合布线将实现楼宇间的数据通信,在规划和设计时应该充分考虑了计算机信息网络系统、语音通信系统及各智能子系统对综合布线系统的要求,力求把综合布线系统建设成一个可靠、开放、高带宽、可扩展、并满足楼宇未来发展的布线系统
二、课题内容(本课题的研究内容、方法、手段及预期成果等)研究内容及方法确定工程实施的范围;现场勘察,了解并记录建筑物情况;确定系统各类信息点接入要求;确定建筑物合适的FD-BD结构;确定综合布线总体设备配置,绘制企业网络综合布线系统结构图;编制楼宇建筑综合布线设计方案;编制中心机房设计方案,确定机房中选用的各项材料;
(6)编制综合布线施工方案及其注意事项预期成果基于综合布线技术操作环境,实现厦门海洋职业学院楼宇网络综合布线设计及通信管理
三、课题工作进度安排(任务完成的阶段安排及时间安排,完成任务所具备的条件因素等)
(1)12月15日—12月18日对教学楼2号楼、公寓楼3号楼进行现场勘查,并收集相关资料;
(2)12月19日—12月22日根据调查和收集的资料列出大概的设计纲要;
(3)12月23日—12月26日完成设计纲要第一部分网络综合布线系统的概述;
(4)12月27日—12月30日完成设计纲要第二部分海院教学楼、公寓楼网络综合布线需求分析;
(5)12月31日—1月4日完成设计纲要第三部分编制楼宇建筑综合布线设计方案;
(6)1月5日—1月9日完成设计纲要第四部分综合布线施工方案;
(7)1月10日—1月14日对方案进行检查修改参考文献资料(要求至少查阅6篇以上正式刊物的文献资料)
[1]刘省贤•综合布线技术教程与实训•北京大学出版社•2006年
[2]余明辉•综合布线系统的设计施工测试验收与维护•人民邮电出版社•2011年
[3]《建筑与建筑群综合布线系统工程设计规范》(GB/T50311-2007)
[4]《建筑与建筑群综合布线系统工程设计规范》(GB/T50311-2007)
[5]黎连业•综合布线系统与施工技术•高等教育出版社•2002年
[6]福禄克网络学院•布线系统测试工程师认证培训教程•2009年
[7]安顺合•智能建筑施工与验收手册•中国建筑工业出版社•2006年
[8]雷锐生•综合布线系统方案设计•西安电子科技大学出版社•2004年
[9]信息产业部•综合布线工程验收规范(GB50312——2007)•中国计划出版社•2007
[10]信息产业部•《GB50314——2007智能建筑设计规范》•中国建筑科技出版社出版•2007年
五、指导教师意见林艺彬同学的网络综合布线系统设计选题符合高职学生的要求,和其所学的专业一致;开题的比较规范,格式符合标准,给予开题指导教师签名陈志贵日期2013年01月09日目录TOC\o1-3\h\u
1.网络综合布线的概述
41.1定义与惯用语
41.2综合布线系统概念
41.
2.1综合布线系统概述
51.
2.2综合布线系统结构示意图
62.厦门海洋学院宿舍楼、教学楼楼网络综合布线需求分析
62.1网络综合布线的概述
72.
1.1本次设计对象
72.
1.2施工对象业务种类需求
72.2现场勘察
82.3确定综合布线网络结构
92.4确定综合布线建筑物FD-BD结构
92.5估算建筑物信息点数
102.6绘制楼宇平面布局图
112.7综合布线产品选型
122.8所选厂家产品及理由
133.编制楼宇建筑综合布线设计方案
133.1综合布线系统概要设计
143.
1.1工程概况
143.
1.2布线系统总体结构
143.
1.3设计目标
153.
1.4设计原则
153.
1.5设计标准
163.
1.6布线产品的选型
163.2综合布线系统详细设计
173.
2.1工作区子系统设计
183.
2.2水平子系统设计
213.
2.3垂直干线子系统设计
233.
2.4管理子系统设计
263.
2.5设备间子系统设计
283.
2.6建筑群子系统设计
323.
2.7综合布线系统详细设计材料总清单
344.综合布线施工方案
354.1工程概况
354.2工程施工的要求
354.
2.1设备安装的要求
364.
2.2管槽系统安装要求
384.
2.3机柜安装要求
394.
2.4信息插座底座安装要求
414.3双绞线施工
424.
3.1双绞线电缆牵引
484.
3.2信息插座端接
494.
3.3配线架端接
504.4光缆施工
504.
4.1光缆传输通道施工52
五、[主要参考文献]57
六、读书笔记57厦门海洋职业学院宿舍楼、教学楼网络综合布线设计
一、[摘要]:随着计算机应用的不断普及,随着网络技术的迅速发展,校园网正逐渐成为学校必备的信息基础设施校园网的实施,为了能够适应新形势发展,各学校充分地利用现有的教学资源进行教学、管理综合布线作为构建智能建筑网络的物理基础利用各种传输介质将通信管理设备和终端连接起来.其性能好坏影响到网络能否正常运行和使用寿命长短校园网建设中最关键的要素就是网络布线,一个学校能否建设成低成本、高性能的校园网,关键看网络布线因此,设计科学、合理、优化的校园网络布线系统,是进一步发挥各种网络设备功能,实现学校各项业务系统的集成,提高应用水平的重点[关键字]:校园网;网络布线系统设备;光线;双绞线;多媒体
1、引言本次设计的对象是厦门海洋职业学院教学楼2号楼与公寓楼3号楼,占地面积大概600平方米左右,楼宇间的通信非常重要,网络综合布线将实现楼宇间的数据通信,在规划和设计时应该充分考虑了计算机信息网络系统、语音通信系统及各智能子系统对综合布线系统的要求,力求把综合布线系统建设成一个可靠、开放、高带宽、可扩展、并满足楼宇未来发展的布线系统设计将完成以下任务确定工程实施的范围;现场勘察,了解并记录建筑物情况;确定系统各类信息点接入要求;确定建筑物合适的FD-BD结构;确定综合布线总体设备配置,绘制企业网络综合布线系统结构图;编制楼宇建筑综合布线设计方案;编制中心机房设计方案,确定机房中选用的各项材料;编制综合布线施工方案及其注意事项
1.网络综合布线的概述
1.1定义与惯用语建筑物与建筑群综合布线系统是建筑物或建筑群内的传输网络,是建筑物内的“信息高速路”它既使话音和数据通信设备、交换设备和其他信息管理系统彼此相连,又使这些设备与外界通信网络相连接它包括建筑物到外部网络或电话局线路上的连接点与工作区的话音和数据终端之间的所有电缆及相关联的布线部件建筑群配线设备(CD)、建筑群子系统、建筑物配线设备(BD)、建筑物干线子系统或光缆、电信间配线设备(FD)、集合点(CP)、信息插座模块、工作区线缆和终端设备(TE)
1.2综合布线系统概念 综合布线是一种楼宇弱电连接系统,通过标准化布线将楼宇内的各种弱电设备和使用设备连接起来现代布线的综合思想就是用一根铜缆支持所有的系统(UTP-4对8芯非屏蔽双绞线)用一种接口支持所有的系统(RJ45接口应用到各种应用系统适配器,再用光纤来加强铜缆的性能)长距离、大带宽传输使用合理的结构化布线可以提供一个统
一、开放的物理布线拓扑结构,使用了合理的标准结构化布线系统可以延长使用寿命,具有可预测的性能且方便管理、网络增长容易以上这些当然可以使公司提高效率、改进生产力以及降低费用
1.
2.1综合布线系统概述结构化布线系统能同时提供用户所需的数据、话音、传真、视像等各种信息服务的线路连接,它使话音和数据通信设备、交换机设备、信息管理系统及设备控制系统、安全系统彼此相连,也使这些设备与外部通信网络相连接它包括建筑物到外部网络或电话局线路上的连线、与工作区的话音或数据终端之间的所有电缆及相关联的布线部件布线系统由不同系列的部件组成,其中包括传输介质、线路管理硬件、连接器、插座、插头、适配器、传输电子线路、电器保护设备和支持硬件1)综合布线系统的基本组成1 工作区一个独立的需要设置终端设备(TE)的区域,即为一个工作区,工作区子系统应由配线水平布线系统的信息插座,延伸到工作站终端设备处的连接电缆及适配器组成2 配线子系统由工作区用的信息插座,每层配线设备至信息插座的配线电缆、楼层配线设备和跳线等组成3 干线子系统应由设备间的配线设备和跳线以及设备间至各楼层配线间的连接电缆组成,在确定干线子系统所需要的电缆总对数之前,必须确定电缆话音和数据信号的共享原则4 建筑子系统应有连接多个建筑之间的主干电缆和光缆、建筑群设备(CD)及设备线缆和跳线组成5 设备间是在每一幢大楼的适当地点设置进线设备、进行网络管理以及管理人员值班的场所设备间子系统由综合布线系统的建筑物进线设备、电话、数据、计算机等各种主机设备及其保安配线设备等组成6 进线间是建筑外部通信和信号管线的入口部位,也可作为入口设施和建筑群配线设备的安装场地7 管理对工作区、电信间、设备间、进线间的配线设备、线缆、信号插座模块等设施按一定的模式进行标识和记录2)综合布线系统的特点1 实用性实施后,布线系统将能够适应现代和未来通信技术的发展,并且实现话音、数据通信等信号的统一传输 2 灵活性布线系统能满足各种应用的要求,即任一信息点能够连接不同类型的终端设备,如电话、计算机、打印机、电脑终端、电传真机、各种传感器件以及图像监控设备等 3 模块化综合布线系统中除去固定于建筑物内的水平缆线外,其余所有的接插件都是基本式的标准件,可互连所有话音、数据、图像、网络和楼宇自动化设备,以方便使用、搬迁、更改、扩容和管理 4 扩展性综合布线系统是可扩充的,以便将来有更大的用途时,很容易将新设备扩充进去 5 经济性采用综合布线系统后可以使管理人员减少,同时,因为模块化的结构,工作难度大大降低了日后因更改或搬迁系统时的费用 6 通用性对符合国际通信标准的各种计算机和网络拓扑结构均能适应,对不同传递速度的通信要求均能适应,可以支持和容纳多种计算机网络的运行
1.
2.2综合布线系统结构示意图图-
1.1综合布线系统结构
2.厦门海洋学院宿舍楼、教学楼楼网络综合布线需求分析
2.1网络综合布线的概述综合布线的含义综合布线是一种模块化的、灵活性极高的建筑物内或建筑群之间的信息传输通道它既能使语音、数据、图像设备和交换设备与其它信息管理系统彼此相连也能使这些设备与外部相连接它还包括建筑物外部网络或电信线路的连接点与应用系统设备之间的所有线缆及相关的连接部件综合布线系统功能1 它是针对计算机与通信的配线系统而设计2 传输模拟与数字的语音;3 传输数据;4 传输传真、图形、图像资料;5 传输电视会议与安全监视系统的信息;6 传输建筑物安全报警与空调控制系统的信息
2.
1.1本次设计对象本次对厦门海洋职业学院宿舍楼、教学楼网络综合布线设计,两栋楼宇形状如下图所示图-
2.1楼宇形状
2.
1.2施工对象业务种类需求现场勘察后对校园综合布线工程区域和信息业务种类需求作了如下详细说明表-
2.1企业综合布线工程区域楼宇名称编号楼宇层数是否有地下室宿舍楼A6否教学楼B5否表-
2.2信息业务种类需求信息业务是/否信息业务是/否语音与数据是图像通信系统是闭路监控否防盗报警否可视对讲否电子门禁否楼宇自控系统否卫星电视接收系统否
2.2现场勘察现场勘察后对楼层吊顶情况、楼宇电缆竖井情况、楼宇设备间、配线间位置作了如下详细说明表-
2.3楼层吊顶情况楼宇名称编号楼宇层次吊顶是否可以打开宿舍楼A6否教学楼B5否表-
2.4楼宇电缆竖井情况楼宇名称编号是否有竖井竖井是否有楼板宿舍楼A否否教学楼B否否表-
2.5楼宇设备间、配线间位置楼宇名称编号设备间位置配线间位置宿舍楼A1楼楼梯口本层楼梯口教学楼B教材准备室教材准备室
2.3确定综合布线网络结构综合布线系统是网络系统应用的物理基础,网络系统的技术特性决定了综合布线系统的体系结构根据企业综合布线信息业务要求及规模,企业组网需求分析结果,选择了树形网络结构,如图(用MicrosoftVisio2003画出)(参考图1-5)#0;��#0;��#0;文本�图-
2.2树形结构
2.4确定综合布线建筑物FD-BD结构经过讨论,分析企业建筑物信息点大约分布情况,绘制出每个楼宇的FD-BD结构图如图(请用MicrosoftVisio2003画出)图-
2.3楼宇BD-FD结构图
2.5估算建筑物信息点数表-
2.6宿舍楼第3栋楼层名称数据点语音点监控有线电视合计648480096548480096448480096348480096248480096148481097表-
2.7教学楼第2栋楼层名称数据点语音点监控有线电视合计56600124660012366001226600121662014注:教室数据点:x
1、语音点x
2、监控x
3、有线电视x4表-
2.8企业建筑物信息点估算楼宇名称数据点语音点监控有线电视宿舍楼3栋27627610教学楼1栋303020合计
306306302.6绘制楼宇平面布局图请用AUTOCAD软件画出每栋楼宇平面图,当每层结构都一样,则只画一层的平面结构图,若不一样,则分开画图-
2.4教学楼二号楼1层图-
2.5教学楼二号楼2-5层图-
2.6宿舍楼三号楼
2.7综合布线产品选型表-
2.9综合布线产品信息表品牌厂商厂家所在地产品线成功案例中国普天中国普天信息产业股份有限公司北京110型配线架、配线箱、跳线、24口配线架、理线器、插座模块、电缆、双绞线、光纤线缆河南大学新校区、重庆大学城、博鳌东屿岛会展中心易蒙EM杭州祺佳计算机网络有限公司杭州光纤光缆、计算机超五类六类线缆、非屏蔽双绞线、屏蔽双绞线、单模多模光纤、信息插座、浙江省贝因美公司无线系统、浙江省工商大学、杭州富士康集团TCL罗格朗山东弘博信息科技有限公司济南综合布线系统、开关插座、智能家居、线缆管理系统山东省政府采购大楼、青岛市国税大厦、中国人民银行东营市支行中电一舟北京中电一舟科技有限公司北京超五类电缆、六类电缆、模板、面板、跳线、数据配线架、110型语音配线架、政府国家广电总局无线局电教楼信息产业部教育部门中国传媒大学宿舍楼AMP安普广州龙鹏信息科技有限公司广州网络机柜、综合布线产品、网络设备安普成功布线苏州金鸡湖大酒店安普成功布线长沙理工大学、国防科技大学安普成功布线广州市轨道交通系统
2.8所选厂家产品及理由根据以上的品牌的对比,决定选用中国普天的产品,根据对中国普天的产品的分析,产品性能稳定、价格合理、技术性能良好、质量保障体系完善、售后服务完善,常在楼宇智能系统工程项目中被作为指定品牌,许多大型和中小型企业选择用普天的综合产品,具备ISO90012000质量管理体系认证、ISO14001环境体系认证、国家CCC认证、泰尔认证、美国UL认证、ETL认证和欧共体CE认证
3.编制楼宇建筑综合布线设计方案
3.1综合布线系统概要设计工作区子系统(workAREASubsystem)又称为服务区子系统Coreragearea,它是由RJ45跳线信息插座与所连接的设备终端或工作站组成信息插座有墙上型、地面型、坐上型等多种在进行终端设备和I/O连接时,可能需要某种传输电子装置,但这种装置并不是工作区子系统的一部分例如,调制解调器,它能为终端与其它设备之间的兼容性传输距离的延长提供所需的转换信号,但不能说是工作区子系统的一部分水平干线子系统又称为水平子系统HorizontalSubsystem水平干线子系统是整个布线系统的一部分,它是从工作区的信息插座开始到管理间子系统的配线架结构一般为星型结构,它与垂直干线子系统的区别在于水平干线子系统总是在一个楼层上,仅与信息插座管理间连接在综合布线系统中,水平干线子系统由4对UTP非屏蔽双绞线组成,能支持大多数现代化通信设备如果有磁场干扰或信息保留时可用屏蔽双绞线如果需要高宽带应用时,可以采用光缆管理间子系统AdministrationSubsystem由交连、互连和I/O组成管理间为连接其它子系统提供手段,它是连接垂直干线子系统和水平干线子系统的设备,其主要设备是配线架、HUB和机柜、电源
3.
1.1工程概况此次设计针对于宿舍楼一栋,教学楼一栋占地面积大约500多平方米宿舍楼楼A栋信息点总共是553个、教学楼B栋信息点总共是62个
3.
1.2布线系统总体结构图-
3.1布线系统总体结构
3.
1.3设计目标主干1000Mbps水平100Mbps交换到桌面的网络传输要求,信息点功能可随需要灵活调整建成后的网络能充分利用Internet、国家信息网、教育网、全国高校互联网上的各种信息,实现资源共享,能够为住在此校区的学生提供丰富的多媒体教学手段,实现高质高效的教学目标学生不出宿舍,就可以在宿舍内访问校园内的大量的共享资源,可以访问电子图书馆、阅览室、邮件服务等高速、安全、稳定的Internet接入由此,我们认为,校园网网络是一个典型的面向未来的网络化、信息化、自动化的集娱乐、教学、办公于一体的,具备多媒体综合业务发展需求的园区网络系统总体设计将本着总体规划、分布实施的原则,充分体现系统的技术先进性、高度的安全可靠性,同时具有良好的开放性、可扩展性本着为学校校区着想,合理使用建设资金,使系统经济可行
3.
1.4设计原则现场勘察,针对要求进行实地考察,考察的对象包括建筑结构、机房设备间和配线管理间的位置、走线路由、电磁环境、布线设施外观以及对建筑物的破坏,如打过墙眼等,并结合场地的平面图而对信息点进行更改,考虑在利用现有空间的同时避开强电及其他线路,做出综合布线调研报告,从而达到更明确有效的为客户进行布线工程
3.
1.5设计标准
(1)国内标准《建筑与建筑群综合布线系统工程设计规范》修订本GBT/T50311—2000《建筑与建筑群综合布线系统工程验收规范》修订本GBT/T50312—2000《市内电信网光纤数字传输系统工程设计暂行技术规定》YDJ44—89《市内电信网光纤数字传输系统工程施工及验收技术规定》YDJ13—88《市内通信全塑电缆线路工程设计规范》YDJ9—90《城市住宅区和办公楼电话通信设施设计标准》YD/T2008—93《中国电气设备安装工程施工及验收规范》GBJ232—82《通信设计安装抗震设计暂行规定》YD2003—92
(2)国际标准IEEE
802.
3、IEEE
802.
4、IEEE
802.
5、IEEE
802.12ISO/IEC11801国际商用建筑物布线标准TIA/EIA568B商务建筑物电信布线标准ITU-TSS:关于ISDN的建议
(1993)FDDI/CDDI/TPDDANSIX3T
9.
53.
1.6布线产品的选型
(1)厂商介绍公司为客户设计、制造和销售产品,所涵盖的行业范围广泛,包括汽车;数据通信系统和消费者电器;电信;航空航天、国防和船舶;医疗;替代能源和照明泰科电子公司是一家公开上市的独立公司,其普通股在纽约证券交易所(NYSE)上市,股票代码为“TEL”泰科电子是全球最大的无源电子元件供应商,主要产品包括连接器和互联系统、继电器、开关、电路保护设备、触摸屏、传感器及电线和电缆主要用于汽车、计算机、消费电子产品、通讯设备、家用电器、航天和国防、工业机械和仪器设备市场
(2)产品特点产品齐全,质量得到保证,拥有良好的售后服务,价格公平合理,技术精良
(3)成功案例简要说明苏州工业园区金鸡湖大酒店位于苏州工业园区金鸡湖和独墅湖这两大天然湖泊之间,占地面积约35公顷经过严格的比较和筛选,酒店选用了泰科电子安普布线综合布线系统构建酒店网络布线系统布线系统全部采用安普六类非屏蔽铜缆系统,电缆采用环保材料的低烟无卤外皮,同时数据主干采用安普高性能的万兆光纤布线系统,保证网络系统高速稳定运行整个系统共计信息点超过10000点普天6类非屏蔽布线系统性能成熟可靠,完全符合并超过国际国内对于六类布线系统的性能要求,已经在国内外各种大型项目中得到成功应用六类系统可以支持更经济的千兆以网解决方案-1000Base-TX降低了千兆以太网的综合建设成本同时,电缆采用环保材料的低烟无卤外皮,保证了网络布线系统的防火安全普天万兆光纤支持低成本高性能的串行传输技术10GBase-SR支持使用成本最低的光源——850纳米光源,以及使用这种光源的电子设备,传输万兆可以达到300公尺或更远的距离另外,采用普天万兆光纤系统传输千兆以太网的传输距离可以延长到900公尺,这意味着当楼间距离超过550米时用户不必采用昂贵的激光器件网络主干可从1G平滑升级到10G不需改变原有的光纤系统
(5)产品选择理由此厂商的产品齐全,质量得到保证,拥有良好的售后服务,价格公平合理,技术精良
3.2综合布线系统详细设计结构化综合布线系统StructuredCablingSystems缩写SCS采用模块化设计和分层星型拓扑结构它能适应任何大楼或建筑物的布线系统其代表产品是建筑与建筑群综合布线系统PremisesDistributionSystem缩写PDS另外,还有两种先进的系统,即智能大楼布线系统IBS和工业布线系统IDS它们的原理和设计方法基本相同,差别是PDS以商务环境和办公自动化环境为主PDS一般采用模块化设计和物理分层星型拓扑结构,传输语音、数据、图像以及各类控制信号一个完善确定设计的布线走线系统,其目标是,在既定时间以外,允许在有新需求的集成过程中,不必再去进行水平布线,损坏建筑装饰而影响审美综合布线系统应能满足所支持的数据系统的传输速率要求,并应选用相应等级的传输缆线和设备综合布线系统应能满足所支持的语音、数据、图像系统的传输标准要求综合布线系统所有设备之间连接端子、塑料绝缘的电缆或、电缆环箍应有色标不仅各个线对是用颜色识别的,而只线束组也使用同一图表中的色标这样有利于维护检修这也是综合布线系统的特点之一
3.
2.1工作区子系统设计图-
3.2工作区
(1)工作区子系统设计要求1用电配置要求在综合布线工程中设计工作区子系统时,要同时考虑终端设备的用电需求每组信息插座附近配备220V电源三孔插座为设备供电,暗装信息插座与其旁边的电源插座应保持200mm的距离,工作区的电源插座应选用带保护接地的单相电源插座,保护接地与零线应严格分开2跳线软线要求1 工作区连接信息插座和计算机间的跳接软线应小于5m2 跳接软线可订购也可现场压接一条链路需要两条跳线,一条从配线架跳接到交换设备,另一条从信息插座连到计算机3信息插座的要求1 每一个工作区信息插座模块(电、光)数量不宜少于2个,并满足各种业务的需求2 低盒数量应以插座盒面板设置的开口数确定,每一个低盒支持安装的信息点数量不宜大于2个3 光纤信息插座模块安装的底盒大小应充分考虑到水平光缆终接处的光缆盘留空间和满足光缆对弯曲半径的要求4 工作区的插座模块应支持不同的终端设备接入,每一个8位模块通用插座应连接1根4对对绞电缆;对每一个双工或2个单工光纤连接器件及适配器连接1根2芯光缆5 从电信间至每一个工作区水平光缆宜按2芯光缆配置6 安装在地面上的信息插座应采用防水和抗压的接线盒7 安装在墙面或柱子上的信息插座的底部离地面的高度宜为300mm8 信息模块材料预算方式如下m=n+n*3%式中m——信息模块的总需求量;n——信息点的总量n*3%——富余量9 现场压接跳线RJ45所需的数量材料预算方式如下m=n*4+n*4*5%式中m——RJ45的总需求量;n——信息点的总量;n*4*5%——留有的富余量
(1)工作区子系统设计原则表-
3.1工作区编号与信息点用途工作区编号位置(房号)面积用途宿舍楼A13101-311228学生宿舍宿舍楼A23201-321228学生宿舍宿舍楼A33301-331228学生宿舍宿舍楼A43401-341228学生宿舍宿舍楼A53501-351228学生宿舍宿舍楼A63601-361228学生宿舍教学楼B-1一楼楼梯旁第一间30教材准备室教学楼B-1210121022104210580(上课期间调用网上资源)教室教学楼B-12103115(上课期间调用网上资源)教室教学楼B-2二楼楼梯旁第一间30播音室教学楼B-2220122022204220580(上课期间调用网上资源)教室教学楼B-22203115(上课期间调用网上资源)教室教学楼B-3三楼楼梯旁第一间30教师课间休息室教学楼B-
32301、
2302、
2304、230580(上课期间调用网上资源)教室教学楼B-32303115(上课期间调用网上资源)教室教学楼B-4四楼楼梯旁第一间30教师课间休息室教学楼B-
42401、
2402、
2404、240580(上课期间调用网上资源)教室教学楼B-42403115(上课期间调用网上资源)教室教学楼B-5五楼楼梯旁第一间30录播控制室教学楼B-5250180录播室教学楼B-525022504250580(上课期间调用网上资源)教室教学楼B-52503115(上课期间调用网上资源)教室
(2)楼宇信息点数统计表表-
3.2宿舍楼A栋楼宇名称数据点语音点监控有线电视合计648480096548480096448480096348480096248480096148481097宿舍楼A栋(信息点总共是577个)(第一层一个监控点)表-
3.3教学楼B栋楼宇名称数据点语音点监控有线电视合计56600124660012366001226600121662014教学楼B栋(信息点总共是62个)(第一层两边楼梯口各一个监控点)表-
3.4总信息点楼宇名称数据点语音点监控有线电视宿舍楼A栋27627610教学B栋303020合计30630630表-
3.5材料清单材料名称品牌型号与规格单位单价数量总价(元)UTP信息模块普天6类个412004800跳线普天 RJ45-RJ45箱652130信息面板普天双口个
430612243.
2.2水平子系统设计
(1)水平子系统的设计原则水平布线子系统将电缆从楼层配线架连接到各用户工作区上的信息插座上,实现信息插座和管理子系统(配线架)之间的连接一般处在同一楼层采用双绞线,为语音及数据的输出点通常可以采用5类8芯4对双绞线,符合或超过EIA/TIA一568标准
(2)管道缆线类型与布放长度1类型1 100W非屏蔽双绞线(UTP)电缆2 100W屏蔽双绞线(STP)电缆3 50W同轴电缆4
62.5/125um光纤电缆2布放长度平均电缆长度=(信息插座至配线间的最远距离+信息插座至配线间的最近距离)/2总电缆长度=平均电缆长度+备用部分(平均电缆长度的10%)+端接容余6m每层用线量C=[
0.55(L+S)+6]*n式中C——每个层楼层的用线量L——服务区内信息插座至配线间的最远距离S——服务区内信息插座至配线间的最近距离n——每层楼的信息插座的数量整座楼的用线量W=∑MCM为楼层数电缆订购数=W/305箱计算JXLB平均电缆长度(JXLB)=(62+8)/2=35m总电缆长度(JXLB)=35+
3.5+6=
44.5mC(JXLB)=[
0.55(62+8)+6]*6=267WJXLB=∑5*267=1335m电缆订购数(JXLB)=1335/305=5箱(不够一箱时按一箱计)GYLA平均电缆长度(GYLA)=(54+6)/2=30m总电缆长度(GYLA)=25+
2.5+6=
33.5mC(GYLA)=[
0.55(54+6)+6]*48=1872mWGYLA=∑6*1872=11232m电缆订购数(GYLA)=11232/305=37箱(不够一箱时按一箱计)表-
3.6材料清单材料名称品牌型号与规格单位单价(元)数量总价(元)RJ45水晶头普天RJ45个1301301双绞线普天3类米330879261电缆普天超五类米850400
(3)信息插座的类型与数量1)最低配置每一个工作区有1个信息插座;每个信息插座的配线电缆为1条4对对绞电缆;完全采用110A交叉连接硬件,并与未来的附加设备兼容;每个工作区的干线电缆至少有2对双绞线2)基本配置每个工作区有2个或2个以上信息插座;每个信息插座的配线电缆为1条4对对绞电缆;具有110A交叉连接硬件;每个工作区的电缆至少有8对双绞线3)综合配置以基本配置的信息插座量作为基础配置;每个工作区的电缆内配有4对双绞线;建筑、建筑群干线或水平布线子系统中配置光缆,并考虑适当的备用量
(4)材料清单表-
3.7材料清单材料名称品牌型号与规格单位单价数量总价(元)信息插座普天EP8个3530621420语音插座普天EP8个35306信息插座普天EP3个
30309003.
2.3垂直干线子系统设计
1.线子系统的设计步骤确定每层楼的干线要求确定整座楼的干线要求确定从楼层到设备间的干线电缆路由确定干线接线间的接合方法选定干线电缆的长度确定敷设附加横向电缆时的支撑结构在敷设电缆时,对不同的介质电缆要区别对待
(1)光纤电缆光纤电缆敷设时不应该绞结光纤电缆在室内布线时要走线槽光纤电缆在地下管道中穿过时要用PVC管光纤电缆需要拐弯时,其曲率半径不能小于30cm光纤电缆的室外裸露部分要加铁管保护,铁管要固定牢固光纤电缆不要拉得太紧或太松,并要有一定的膨胀收缩余量光纤电缆埋地时,要加铁管保护
2、同轴粗电缆同轴粗电缆敷设时不应扭曲,要保持自然平直粗缆在拐弯时,其弯角曲率半径不应小于30cm粗缆接头安装要牢靠粗缆布线时必须走线槽粗缆的两端必须加终接器,其中一端应接地粗缆上连接的用户间隔必须在
2.5m以上粗缆室外部分的安装与光纤电缆室外部分安装相同
3、双绞线双绞线敷设时线要平直,走线槽,不要扭曲双绞线的两端点要标号双绞线的室外部要加套管,严禁搭接在树干上双绞线不要拐硬弯
4、同轴细缆同轴细缆的敷设与同轴粗缆有以下几点不同细缆弯曲半径不应小于20cm细缆上各站点距离不小于
0.5m一般细缆长度为183m,粗缆为500m
(2)根据建筑物实际情况,确定垂直干线路由,绘制布线路由图图-
3.3教学楼布线路由图图-
3.4公寓楼布线路由图
(3)确定垂直子系统设计方案垂直干线子系统也称为垂直子系统由设备间的建筑物配线设备BD和跳线,以及设备间至各楼层配线问的干线电缆组成干线子系统应选择干线电缆较短,安全和经济的路由,宜选择带门的封闭型综合布线专用的通道敷设干线电缆干线电缆宜采用点对点端接,也可采用分支递减端接如果设备间与计算机机房和交换机机房处于不同的地点,而且需要将话音电缆连至交换机机房,数据电缆连至计算机机房,则宜在设计中选取不同的干线电缆或干线电缆的不同部分,来分别满足话音和数据的需要当需要时,也可采用光缆系统
(4)线缆敷设方案垂直干线子系统宜采用星状拓扑结构无机械损伤的电或改缆,内线缆的敷设扩建工程使用的电缆,可采用沿墙明敷方式新建的建筑物内或要求管线隐蔽的电缆应采用暗管敷设方式易受外部损伤的线路;线路路由上,其他管线和障碍物较多,不宜明敷的线路;易受电磁干扰或易爆易燃的危险场所的线路可以采用明管配线
(5)材料清单表-
3.8材料清单材料名称品牌型号与规格单位数量双绞线普天0-1664162箱
253.
2.4管理子系统设计
(1)确定管理间子系统设计方案用户可以在管理子系统中更改、增加、交接、扩展线缆用于改变线缆路由建议采用合适的线缆路由和调整件组成管理子系统管理子系统是对线缆的管理,对每条线缆进行编号如下表对每层的双绞线进行房间号及a/b结合标记,用a表示是网络线,用b表示是电话线,用每个房间的房间号后跟a或b再跟数字来标记每个房间所接的网络线还是电话线,后面的数字表明所接的线缆的个数如A604a1表示A604接的网络线个数是一个,依次类推表-
3.9宿舍楼A栋的线缆标记3101a43101b43102a43102b43103a43103b
4......3112a43112b43201a43201b43202a43202b43203a43203b
4......3212a43212b43301a43301b43302a43302b43303a43303b
4......3312a43312b43401a43401b43402a43402b43403a43403b
4......3412a43412b43501a43501b43502a43502b43503a43503b
4......3512a43512b43601a43601b43602a43602b43604a43604b
4.......3612a43612b4表-
3.10教学楼B栋的线缆标记a1b1教材准备室2101a12101b12102a12102b12103a12103b12104a12104b12105a12105b1a1b1播音室2201a12201b12202a12202b12203a12203b12204a12204b12205a12205b1a1b12301a12301b12302a12302b12303a12303b12304a12304b12305a12305b1a1b1教师课间休息室2401a12401b12402a12402b12403a12403b12404a12404b12405a12405b1a1b1录播室2501a12501b12502a12502b12503a12503b12504a12504b12505a12505b1
(2)管理间编号表-
3.11宿舍楼管理间编号楼层管理间位置编号机柜、机架安装方式6无无无5无无无4无无无3无无无2无无无1楼梯口001L立式机柜表-
3.12教学楼2号楼管理间编号楼层管理间位置编号机柜、机架安装方式1教材准备室JXL21立式机柜2播音室JXL22立式机柜3教师课间休息室JXL23立式机柜4教师课间休息室JXL24立式机柜5录播控制室JXL25立式机柜表-
3.13材料清单材料名称品牌型号与规格单位单价数量总价(元)语音配线架普天50口台1005500语音配线架普天100口台25082000数据配线架普天48口台
280926203.
2.5设备间子系统设计电信间的基本要求1 电信间的数量应按照所服务的楼层范围及工作区面积来确定如果该层信息点数量不大于400个,水平线缆长度在90m范围以内,宜设置一个电信间;当超出这一围宜设两个或多个电信间;每层的信息点数量数较少,且水平线缆长度不大于90m的情况下,宜几个楼层合设一个电信间2 电信间应与强电间分开设置,电信间内或其紧邻处应设置线缆竖井3 电信间的使用面积不应小于5㎡,也可根据工程中配线设备和网络设备的容量进行调整4 电信间应提供不少于两个220v带保护接地的单相电源插座,但不作为设备电源5 电信间应采用外开丙级防火门,门宽大于
0.7m电信间内温度应为10℃~35℃,相对湿度宜为20﹪~80﹪.设备间基本要求1 设备间位置应根据设备的数量、规模、网络构成等因素,综合考虑确定2 每幢建筑物内应至少设备1个设备间,如果电话交换机与计算机网络设备安装在不同的场地或根据安全需要,也可设置2个或2个以上设备间,以满足不同业务的设备安装需要3 建筑物综合布线系统与外部配线网连接时,应遵循相应的接口标准要求4 设备间的设计应符合下列规定a.设备间宜处于干线子系统的中间位置,并考虑主干线缆的传输距离与数量b.设备间尽可能靠近建筑物线缆竖井位置,有利于主干线缆的引入c.设备间的位置宜便于设备接地d.设备间应尽量远离高低压变配电、电机、X射线、无线电发射等有干扰源存在的场地e.设备间室温度应为10℃~35℃,相对湿度应为20﹪~80﹪,并应有良好的通风f.设备间内应有应有足够的设备安装空间,其使用面积不小于10㎡,该面积不包括程控用户交换机、计算机网络设备等设施所需是面积在内g.设备间粱下净高不应小于
2.5m采用外开双扇门,门宽不应小于
1.5m5 设备间应防止有害气体侵入,并有良好的防尘措施 6 设备间应按照防火标准按照相应的防火报警装置,使用防火防盗门7 在地震区的区域内,设备安装应按规定进行抗震加固8 设备安装宜符合下列规定a.机架或机柜前面的净空不应小于800mm后面的净空不应小于600mmb.壁挂式配线设备底部离地面的高度不宜小于300mm.9 设备间应提供不少于220v带保护接地的单相电源插座,但不作为设备供电电源10 设备间如果安装电信设备或其他信息网络设备时,设备供电应符合相应的设计要求
3.设备间线缆敷设1).活动地板目前有两种敷设方法1 正常活动地板高度为300~500mm,地板下面空间较大,除敷设各种线缆外还可兼作空调送风通道2 简易活动地板高度为60~200mm,地板下面空间小,只作线缆敷设用,不能作为空调送风通道两种活动地板在新建建筑中均可使用,一般用于电话交换机房,计算机主机房和设备间简易活动地板下空间较小,在高层不高的楼层尤为适用,可节省净高空间,也适用于已建成的原有建筑或地下管线和障碍物较复杂且断面位置受限制的区域其优点如下:线缆敷设和拆除均比较简单方便,能适应线路增减变化,有较高的灵活性,便于维护管理地板下空间大,线缆容量和条数多,路由自由短捷,节省线缆费用不改变建筑结构其缺点如下:造价较高会减少房屋的净高对地板表面材料在耐冲击性,耐火性和抗静电能力方面有一定的要求
2.地板和墙壁内沟槽线缆在建筑的预先建成的墙壁或地板内的沟槽中敷设时,沟槽的大小根据线缆容量来设计,上面设置盖板保护,地板或墙壁内沟槽敷设方式只适用于新建建筑,在已建建筑中建安采用,因不易制成暗敷沟槽,沟槽敷设方式只能在局部段落中使用,不宜在面积较大的房间内全部采用在今后有可能变化的建筑中不宜使用沟槽敷设方式,因为沟槽方式是在建筑中预先制成飞,所以在使用会受到限制,线缆路由不能自由和变动
3.预埋管路在建筑的墙壁或楼板内预埋管路,其管径和根数根据线缆需要来设计,预埋管路只用新建建筑,管路敷设段落必须根据线缆分布方案要求设计,预埋管路必须在建筑施工中建成,所以用会受到限制,必须精心设计和考虑其优点如下:穿放线缆比较容易,对维护,检修和扩建均有利造价低廉,技术要求不高不会影响房屋建筑结构其缺点如下:管路容纳线缆的条数少,设备密度较高的场所不宜采用线缆改建或增设有所限制线缆路由受管路限制,不能变动
4.机架在机架柜上安装桥架的敷设方式,桥架的尺寸根据线缆需要设计,在已建或新建的建筑中均可使用这种敷设方式,它的适应性较强,适用场合较多其优点如下:不受建筑的设计和施工限制,可以建成后安装便于施工和维护,也有利于扩建能适应见后变动的需要其缺点如下:线缆敷设不隐蔽,不美观(除暗敷外)在设备(机架)上或沿墙安装走线架(或槽道)较复杂增加施工操作程序机架上安装走线架或槽道在层高较低的建筑中不宜使用
(2)确定设备间子系统设计方案 综合布线设备间是在建筑物内的适当地点安装进线和集线设备,实施网络管理,也是管理人员值班的场所 设备间内的所有进线终端设备应采用色标区别各类用途的配线区 设备间的位置及大小,应根据设备的数量、规模、最佳网络中心等内容综合考虑确定通常情况下,设备间管理子系统建议选择在水平中心位置,可以保证水平布线的距离最短,不会超过双绞线所允许的100m最大传输距离 设备间既要按照有关标准和技术规范,根据选用设备及安装要求进行设计和规划,又要满足采光、防尘、隔音等工作环境的要求 设备间装修时,应尽量保持室内无尘土,通风良好,应符合有关消防规范,配置有关消防系统 按照标准的设计要求,设备间尤其是要集中放置设备的设备间应尽量满足下面的要求: 设备间应当选择设置在电梯附近,以便装运笨重的设备 设备间的最小安全尺寸是28OcmX2OOcm,标准的天花板高度为24Ocm,门的大小至少为
2.1mx1m,向外开尽量将设备柜放在靠近竖井的位置,在柜子上方应装有通风口用于设备通风 房顶吊顶一般要取齐过梁下部,并留足灯具和消防设备暗埋高度建议吊顶采用铝合金龙骨和防火石棉板 设备间地板优先使用耐磨防静电贴面的防静电地板,抗静电性能较好,长期使用无变形、褪色等现象设备间的地板负重能力至少应为5OOkg/mz 由于设备间多采用下进线方式,地板下要敷设走线槽和通风,因此,地板净空高度应当为10-5Ocm 设备间设备一般按机柜间与操作间相隔离的原则进行安装,特别是对于交换机、光传输设备、集群设备等自动化程度高,网管系统可完成设备大部分调测监控及系统操作的设备,这样可减少人为因素对设备的影响 为隔音、防尘需装设双层合金玻璃窗,配遮光窗帘,配置专用通风、滤尘设备,保持设备间通风良好 室内照明不低于1501x 设备间室温应保持在10@25C之间,相对温度应保持60%-80% 设备间尽量远离存放危险物品的场所和电磁千扰源无线电干扰场强,在频率范围为0 l5MHz@l0OOMHz时不大于120佃机房内磁场干扰场强不大于800川m 平行线缆相互隔离的距离不小于50一6Ocm 竖井通过楼层时要尤其注意,尽量保持间距,避免电力线千扰通信传输在设备间、站区通信、电力线密集人井、电缆房中,更要注意各自的盘绕、路径的最优布设
(2)材料清单表-
3.14材料清单材料名称品牌型号与规格单位单价数量总价(元)电缆普天50对米15150022500光缆普天单模光缆米
3160048003.
2.6建筑群子系统设计
(1)建筑群子系统的规划和设计建筑群子系统主要应用于多幢建筑物组成的建筑群综合布线场合,单幢建筑物的综合布线系统可以不考虑建筑群子系统建筑群子系统的设计主要考虑布线路由选择、线缆选择、线缆布线方式等内容考虑环境美化要求建筑群主干布线子系统设计应充分考虑建筑群覆盖区域的整体环境美化要求,建筑群干线电缆尽量采用地下管道或电缆沟敷设方式考虑建筑群未来发展需要线缆布线设计时,要充分考虑各建筑需要安装的信息点种类、信息点数量,选择相对应的干线电缆的类型以及电缆敷设方式,使综合布线系统建成后,保持相对稳定,能满足今后一定时期内各种新的信息业务发展需要线缆路由的选择考虑到节省投资,线缆路由应尽量选择距离短、线路平直的路由但具体的路由还要根据建筑物之间的地形或敷设条件而定在选择路由时,应考虑原有已铺设的地下各种管道,线缆在管道内应与电力线缆分开敷设,并保持一定间距电缆引入要求建筑群干线电缆、光缆进入建筑物时,都要设置引入设备,并在适当位置终端转换为室内电缆、光缆引入设备应安装必要保护装置以达到防雷击和接地的要求干线电缆引入建筑物时,应以地下引入为主,如果采用架空方式,应尽量采取隐蔽方式引入建筑群子系统布线线缆的选择建筑群子系统敷设的线缆类型及数量由综合布线连接应用系统种类及规模来决定一般来说,计算机网络系统常采用光缆作为建筑物布线线缆,在网络工程中,经常使用
62.5μm/125μm(
62.5μm是光纤纤芯直径,125μm是纤芯包层的直径)规格的多模光缆,有时也用50um/125um和100um/140um规格的多模光纤户外布线大于2km时可选用单模光纤电话系统常采用3类大对数电缆作为布线线缆,类大对数双绞线是由多个线对组合而成的电缆,为了适合于室外传输,电缆还覆盖了一层较厚的外层皮有线电视系统常采用同轴电缆或光缆作为干线电缆电缆线的保护当电缆从一建筑物到另一建筑物时,要考虑易受到雷击、电源碰地、电源感应电压或地电压上升等因数,必须用保护这些线对如果电气保护设备位于建筑物内部(不是对电信公用设施实行专门控制的建筑物)那么所有保护设备及其安装装备都必须有UL,安全标记2.建筑群干线子系统的工程设计的步骤
①确定敷设现场的特点包括确定整个工地的大小、工地的地界、建筑物的数量等
②确定电缆系统的一般参数包括确认起点、端接点位置、所涉及的建筑物及每座建筑物的层数、每个端接点所需的双绞线的对数、有多个端接点的每座建筑物所需的双绞线总对数等
③确定建筑物的电缆入口
④确定明显障碍物的位置
⑤确定主电缆路由和备用电缆路由
⑥选择所需电缆的类型和规格
⑦确定每种选择方案所需的劳务成本
⑧确定每种选择方案的材料成本
⑨选择最经济、最实用的设计方案3.建筑群干线子系统管槽路由设计
(1)地下方式:
①管道电缆
②电缆沟
③直埋电缆
(2)架空方式:
①架空电缆
②墙壁电缆
(3)材料清单表-
3.15材料清单材料名称品牌型号与规格单位单价数量总价(元)电缆普天50对米15250037500光缆普天单模光缆米
3220066003.
2.7综合布线系统详细设计材料总清单表-
3.16设计材料总清单材料名称品牌型号与规格单位单价数量总价跳线普天 RJ45-RJ45箱70170跳线普天6类条63141884UTP信息模块普天6类个
3.712004440信息面板普天双口个3306918信息插座普天EP8个73062142语音插座普天EP8个63061836连接器普天LC个
1.5600900双绞线普天6类箱5007437000光缆普天多模光缆箱6007444400光缆普天单模光缆米225005000电缆普天50对米15200030000双绞线配线架普天6类个11801416520语音配线架普天50口台1005500语音配线架普天100口台25082000数据配线架普天48口台25092750机柜普天立式台
4501463004.综合布线施工方案
4.1工程概况此次综合布线施工对象是厦门海洋职业学院教学楼2号楼和宿舍楼3号楼
4.2工程施工的要求
1、综合布线系统工程安装施工,须按照《综合布线系统工程验收规范》GB50312一2007中的有关规定进行安装施工也可以根据工程设计要求办理
2、智能化小E的综合布线系统工程中,其建筑群主干布线子系统部分的施工,与本地电话网路有关,因此,安装施工的基本要求应遵循我国通信行业标准《本地电话网用户线线路工程设计规范》YD5006一95等标准中的规定
3、综合布线系统工程中所用的缆线类型和性能指标、布线部件的规格以及质量等均应符合我国通信行业标准《大楼通信综合布线系统第1-3部分》YD/T
926.1一
2001、YD/T
926.2一
2001、YD/T
926.3一2001等规范或设计文件的规定,工程施工中,不得使用末经鉴定合格的器材和设备
4、应按照规范要求进行综合布线工程施工质量检查、随工检验和竣工验收建设单位应通过工程监理人员或工地代表严格进行工程技术监督,及时组织隐蔽工程的检验和签证工作
5、大项目应成立工程项目部,由项目部负责工程的整体实施、规划和协调工作,根据实际的需求和资金的投入,确保工程进度、质量以及按照工程施工规范要求与其他工程之间的协调做好材料、设备的采购及发放管理工作
6、做好项目跟踪报告和项目文档的管理,所有文件均应当使用国际计量单位制工程中所提交的全部文件和图纸均应清晰、完整,并按综合布线标准和有关建筑标准制作
7、文明、安全施工施工中须戴安全帽,身穿工作服使用电源时,应按照《电气装置安装工程施工及验收规范》中的标准执行,严禁随意搭线和安全通道相交架设,防止火灾隐患
8、综合布线系统工程施工应与土建施工配合,做好预留孔洞,在浇铸混凝土前将管路、接线盒和配线柜的基础安装部分预埋好表面辐射工程应配合土建和装饰工作,力求统一进度
9、工程完毕后,应做好布线工程所涉及的线缆及器件的测试工作,应按照规范执行
4.
2.1设备安装的要求
1.机架安装要求1)机架安装完毕后,水平、垂直度应符合厂家规定若无厂家规定时,垂直度偏差度不应大于3mm2)机架上的各种零件不得脱落或碰坏,漆面若有脱落应予以补漆,各种标志完整清晰3)机架的安装应牢固,应按施工图的防振要求进行加固4)安装机架面板,架前应留有
1.5M空间,机架背后离墙距离应大于
0.8m,以便于安装和施工5)壁挂式机架距地面宜为300-800mm
2.配线设备机架安装要求1)采用下走线方式时,架底位置应与电缆上线孔相对应2)各直列垂直倾斜误差不大于3MM,底座水平误差每平米不应大于2mm3)接线端子各种标志应齐全4)交接箱或暗线箱宜暗设在墙体内预留墙洞安装,箱底高出地面宜为500-1000mm
3.信息插座安装要求1)安装在活动地板或地面上,应固定在接线盒内,插座面板有直立和水平等形式;接线盒盖可开启,并能严密防水、防尘接线盒盖面应与地面齐平2)安装在墙体上,宜高出地面300mm,若地面采用活动地板时,应加上活动地板净高尺寸3)信息插座底座的固定方法以施工现场条件而定,以采用膨胀螺钉、射钉等方式4)固定螺钉应拧紧,不得产生松动现象5)信息插座应有标签,以颜色、图形、文字表示所接终端设备类型6)安装位置应符合设计要求
4.电缆桥架及槽道安装要求1)桥架及槽道的安装位置应符合施工图规定,左右偏差不应超过50mm2)桥架及槽道水平度每米偏差不应超过2mm3)垂直桥架及槽道应与地面保持垂直,并无倾斜现象,垂直度偏差不应超过3mm4)两槽道拼接处水平偏差不应超过2mm5)吊架安装应保持垂直,整齐牢固,无歪斜现象6)金属桥架及槽道节与节间应接触良好,安装牢固
5.各类接线模块安装要求1)模块设备应完整,安装就位,标志齐全2)安装螺钉必须拧紧,面板应保持在一个水平面上
6.安装机架、配线设备及金属钢管、槽道的接地体应符合设计要求,并保持良好的电气连接
4.
2.2管槽系统安装要求1暗埋缆线的安装和施工方案1)设备间的土建工程已全部竣工,室内墙壁已充分干燥设备间门的高度和宽度应不妨碍设备的搬运,房门锁和钥匙齐全;2)设备间地面应平整光洁,预留暗管、地槽和孔洞的数量、位置、尺寸均应符合工艺设计要求;3)电源已经接入设备间,应满足施工需要;4)设备间的通风管道应清扫干净,空气调节设备应安装完毕,性能良好;5)在铺设活动地板的设备间内,应对活动地板进行专门检查,地板板块铺设严密坚固,符合安装要求,每平米水平误差应不大于2mm,地板应接地良好,接地电阻和防静电措施应符合要求2施工要求线槽安装位置应符合施工图规定,左右偏差视环境而定,最大不应超过50mm;线槽水平每米偏差不应超过2mm;垂直线槽应与地面保持垂直,并无倾斜现象,垂直度偏差不应超过3mm;线槽节与节间用接头连接板拼接,螺钉应拧紧两线槽拼接处水平度偏差不应超过2mm;当直线段桥架超过30m或跨越建筑物时,应有伸缩缝其连接宜采用伸缩连接板;线槽转弯半径不应小于其槽内的线缆最小允许弯曲半径的最大者盖板应紧固支吊架应保持垂直,整齐牢靠,无歪斜现象3明装线槽的施工方案线槽安装位置应符合施工图规定,左右偏差视环境而定,最大不应超过50mm;线槽水平每米偏差不应超过2mm;垂直线槽应与地面保持垂直,并无倾斜现象,垂直度偏差不应超过3mm;线槽节与节间用接头连接板拼接,螺钉应拧紧两线槽拼接处水平度偏差不应超过2mm;当直线段桥架超过30m或跨越建筑物时,应有伸缩缝其连接宜采用伸缩连接板;线槽转弯半径不应小于其槽内的线缆最小允许弯曲半径的最大者盖板应紧固支吊架应保持垂直,整齐牢靠,无歪斜现象4桥架布线施工方案
4.
2.3机柜安装要求1机柜与设备的排列布置以交替模式排列设备行,即机柜/机架面对面排列以形成热通道和冷通道冷通道是机架/机柜的前面区域,热通道位于机架/机柜的后部采用从前到后的冷却配置针对线缆布局,电子设备在冷通道两侧相对排列,冷气从钻孔的架空地板吹出热通道两侧电子设备则背靠背,热通道下的地板无孔,天花板上的风扇排出热气地板上用于走线的开口不宜大于需要减震器或毛刷课安装在开口处阻塞气流为更好利用现有的制冷,排风系统,在数据中心设计和施工的时候,应避免造成迂回气流,造成热空气没有直接排除计算机机房;避免架空地板下空间线缆杂乱堆放,阻碍气流的流动;避免机柜内部线缆堆放太多,影响热空气的排放在没有满载的机柜中,建议采用空白挡板以防止“热通道”气流进入“冷通道”,造成迂回气流对于适中的热负荷,机柜可以采用以下任何通风措施通过前后门上的开口或孔通风,提供50%以上开放空间,增大通风开放尺寸和面积能提高通风效果;采用风扇,利用门上通风口和设备与机架门间的充足的空间推动气流通风 对于高的热负荷,自然气流效率不高,要求强迫气流为机柜内所有设备提供足够的冷却强迫气流系统采用冷热通道系统附加通风口的方式 安装机柜风扇时要求不仅不能破坏冷热通道性能,而且要能增加其性能来自风扇的气流要足够驱散机柜发出的热量在数据中心热效率最高的地方,风扇要求从单独的电路供电,避免风扇损坏时中断通信设备和计算机设备的正常运行
(2)机柜/机架摆放机柜和机架放置时要求前面或后面边缘沿地板边缘排列,以便于机柜和机柜前面和后面的地板取出用于机柜走线的地板开口位置应该置于机柜下方或其他不至于造成阻塞的位置;用于机柜走线的地板开口位置应该位于机柜间的垂直线缆管理器的下方,或位于机柜下方的底部拐角处通常,在垂直线缆管理器下安置开口更可取地板上用于走线的开口不宜大于需要,任何的情况下,地板开口处都应该沿地板边缘排列机柜和机柜的摆放位置应与照明设施想协调主机房内通道与设备间的距离应符合下列规定
1.用于运输设备的通道净宽不应小于
1.5m
2.面对面布置的机柜或机柜正面之间的距离不宜小于
1.2m
3.背对背布置的机柜或机柜背面之间的距离不宜小于1m
4.当需要在机柜侧面维修测试时,机柜与机柜,机柜与墙之间的距离不宜小于
1.2m
5.成行排列的机柜,其长度超过6m时,两端应设有走道;当两个走道之间的距离超过15m时,其间还应增加走道;走道的宽度不宜小于1m,局部可为
0.8m3机柜轨道调整机柜要求有可前后调整的轨道轨道要求提供42U或更大的安装空间每U单元都应标记以简化设备布置设备和连接硬件要求固定在机架的轨道上,便于最有效地利用机柜空间如果配线架安装在机柜前面,为了给配线架和门之间的线缆管理提供空间,前面轨道应至少缩进100mm同样,如果配线架安装在机柜背面背面轨道至少缩进100mm为防止触及配线架背面,配线架不能同时安装在同一机柜或机架前后轨道上如果电源板安装子啊机柜的前面或后面轨道,要为电源和电源线提供足够的净空间4机柜抗震设计抗震机架/机柜应用螺栓栓紧到抗震底座上或直接安装到混凝土楼板上5机柜进线及理线
1.线缆敷设至电信间后,以楼层、房间、工作区的顺序,依据将线缆整理进机柜机柜里线缆根据端接位置、盘缆要求应预留6到6米长度线缆以下是几种常见的进线方式1 机柜顶部进线2 活动地板机柜地步进线3 水泥地板机柜地步进线
2.线缆与接续模块本接要求机柜和机柜放置时要求前面或后面边缘沿地板边缘排列,以便于机柜和机柜前面和后面的地板取出成行排列的机柜,其长度超过6m时,两端应设有走道;当两个走道之间的距离超过15m时,其间还应增加走道;走道的宽度不宜小于1m,局部可为
0.8m
3.设备间机柜理线要求成行排列的机柜,其长度超过6m时,两端应设有走道;当两个走道之间的距离超过15m时,其间还应增加走道;走道的宽度不宜小于1m,局部可为
0.8m根据国标,垂直桥架内的线缆每隔
1.5米应绑扎一次(防止线缆应重量产生拉力造成线缆变形),对水平桥架内并没有要求而终端面板、机柜、配线架、配线箱按照标准必须做到两底角平行,因此布线系统的美观就主要集中在设备间内的线缆部分设备间内的线缆往往会进入机柜配线架或壁挂配线架在本文中将主要涉及机柜型配线架的理线工艺
4.
2.4信息插座底座安装要求1底盒安装要求底盒不要预埋太深,标高不一;面板与墙体间有缝隙,面板切记不要有胶漆污染,不平直2面板安装要求面板有3种安装方式1 安装在地面上,要求安装在地面上的金属底盒应当是密封的,防水,防尘,可带有升降的功能此安装方法对于设计安装造价较高,并且由于事先无法预知工作人员的办公位置,也不知分隔板的确切位置,因此灵活性不是很好2 安装在分隔板上,此方法适用于分隔板位置确定后的情况,安装造价较为便宜3 安装在墙上面板又分为固定式面板和模块化面板,固定式面板的信息模块与面板合为一体,无法去掉某个信息模块或更换其他类型的信息模块固定式的优点价格便宜,便于安装,缺点是结构不能改变,在局域网中应用较少模块化面板使用预留了多个插孔位置的通用面板,面板与信息模块可以分开购买由于存在结构上的差异,不同厂商的面板的信息模块可能不配套,除非有配套安装产品说明,否则面板和信息模块要求购买同一厂商的产品在地板上进行模块化面板安装时,需要选用专门的地面插座铜质地板插座有旋盖式,翻扣式和弹启式3种,铜面分为圆,方两面其中弹启式地面插座应用最广,它采用铜合金或铝合金材料制作而成,安装于厅,室内任意位置的地板平面上,适用于大理石,木地板,地毯和架空地板等各种地面使用时,面盖与地板相平不影响通行及打扫,而且在闭合的面盖上行走时,即使踩上了面盖也不容易弹出,地面插座的防渗结构可保证水滴等在插座底盒上的流体不易渗入还有几类面板应用在一些特殊场合,如表面安装盒,对媒体信息端口,区域接线盒,多媒体面板和家具模块化面板
4.3双绞线施工一.任务分析双绞线结构双绞线(TwistedPairTP)由两根22~26号绝缘铜导线相互缠绕而成,如果一对或多对双绞线放在一个绝缘套管中便构成了双绞线电缆在双绞线电缆内,不同线对具有不同的扭绞长度把两根绝缘的铜导线按一定密度相互绞合在一起,可降低信号干扰的程度,每一根导线在传输中辐射出来的电波会另一根线上发出的电波抵消,一般扭线越密其抗外来电磁信号干扰的能力就越强与光缆相比,双绞线在传输距离信道宽度和数据传输速度方面均受一定限制,但价格较为低廉,布线成本较低,施工方便双绞线的种类和型号按结构分类双绞线电缆可分为非屏蔽和屏蔽双绞线电缆按性能指标分类,双绞线电缆可分为1类、2类、3类、4类、5类、5e类、6类、7类双绞线电缆按双绞线电缆对数多少进行分类,有2对、2对、4对双绞线电缆和25对、50对100对的大对数双绞线双绞线电缆类型1 1类双绞线(Cat1)缆线最高频率带宽是75khz,用于报警系统或语音系统2 2类双绞线(Cat2)缆线最高频率带宽是1MHz,用于语音、EIA-
232.3 3类双绞线(Cat3)3类/C级电缆的频率带宽最高为16MHz4 4类双绞线(Cat4)缆线最高频率带宽为20MHz,最高数据传输速率为20Mbit/s.5 5类双绞线(Cat5):5类/D级电缆增加了绕线密度,外套为高质量的绝缘材料6 超5类双绞线(Cat5e)7 6类双绞线(Cat6)二.相关知识
(一)工具准备
1.线缆敷设工具
2.双绞线缆端接工具
(1)剥线钳
(2)压线工具
(3)110打线工具
3.标识工具
(二)线缆整理材料准备
1.扎带
2.理线架(环)1 垂直理线架可安装于机架的上下两端或中部,完成线缆的前后双向垂直管理2 水平理线架安装于机柜或机架的前面,线缆从机架式配线架搭配使用,提供配线架或设备跳线水平方向的线缆管理3 机架顶部理线槽可安装在机架顶部,线缆从机柜顶部进入机柜,为进出的线缆提供一个安全可靠的路径
(3)标签材料准备1.线缆标签普通不干标签覆盖保护膜线标签套管标签2.场标签3.配线架标签4.信息插座面板标签
3.任务实施
(1)敷设双绞线缆
1.敷设双绞线缆的基本要求
(1)槽道检查在布放电缆之前,对线缆经过的所有路由进行检查,清除槽道接连处的毛刺和突出尖锐物,清洁掉槽道里的铁屑、小石块、水泥碴等物品,保障一条平滑畅通的槽道
(2)文明施工在槽道中敷设线缆应采用人工牵引,牵引速度要慢,不宜猛拉紧拽,以防止线缆外护套发生被磨、刮、蹭、拖等损伤不要在布满杂物的地面大力抛摔和拖放电缆;禁止踩踏电缆;布线路由较长时,要多人配合平缓地移动,特别在转角处,应安排人值守理线;线缆的布放应自然平直,不得产生扭绞、打圈、接头等现象,不应受外力的挤压和损失
(3)为了准确核算线缆用量,充分利用线缆,对每箱线从第一次放线起,做一个放线记录表线缆每个两英尺有一个长度记录,标准包装每箱线长1000英尺(305m)每个信息点放线时记录开始处和结束处的长度,这样对本次放线的长度和线箱中剩余线缆的长度一目了然,并将线箱中剩余线缆布放至合适的信息点
(4)线缆应有余量以适应终接、检测和变更对绞电缆预留长度在工作区宜为3-6cm,电信间宜为
0.5-5m;有特殊要求的应按设计要求预留长度
(5)桥架及线槽、内线缆绑扎要求槽内线缆布放应平齐顺直、排列有序,尽量不交叉,在线缆进出线槽部位、转弯处应绑扎固定线缆在桥架内垂直敷设时,在线缆的上端和每间隔
1.5m处应固定在桥架的支架上;水平敷设时,在线缆的首、尾、转弯及没间隔5-10m处进行固定在水平、垂直桥架中敷设线缆时,应对线缆进行绑扎对绞电缆、光缆及其他信号电缆应根据线缆的类别、数量、缆径芯数分束绑扎绑扎间距不宜大于
1.5m,间距应均匀,不宜绑扎过紧或使线缆受到挤压
(6)电缆转弯时弯曲半径应符合的规定非屏蔽4对对绞电缆的弯曲半径应至少为电缆外径的4倍屏蔽4对对绞电缆的弯曲半径应至少为电缆外径的8倍主干对绞电缆的弯曲半径应至少为电缆外径的10倍
(7)电缆与其他线管距离电缆尽量远离其他管线,与电力及其他管线的距离要符合GB50311——2007中的规定
(8)预埋线槽和暗管敷设线缆应符合的规定敷设线槽和暗管的两端宜用标志表示出编号等内容预埋线槽宜采用金属线槽,预埋或密封线槽的截面利用率应为30%-50%敷设暗管宜采用钢管或阻燃聚氯乙烯硬质管布放大对数主干电缆及4芯以上光缆时,直线管道的管径利用率应为50%-60%,弯管道应为40%-50%暗管布放4对对绞电缆或4芯及一下光缆时,管道的截面利用率应为25%-30%
(9)拉绳速度和拉力拉绳缆的速度从理论上讲,线的直径越小,则拉的速度越快但是,有经验的安装者采取慢速而又平稳的拉绳,而不是快速的拉绳原因是快速拉绳会造成线缆的缠绕或被绊住拉力过大,线缆变形,会引起线缆传输性能下降线缆最大允许拉力如下
①1根4对双绞线电缆,拉力为100N(10kg)
②2根4对双绞线电缆,拉力为150N(15kg)
③3根4对双绞线电缆,拉力为200N(20kg)
④n根4对双绞线电缆,拉力为(n×50+50)N
⑤25对5类UTP电缆,最大拉力不能超过40kg,速度不宜超过15m/min
2.敷设水平双绞线
(1)暗道敷设暗道布线是在浇筑混泥土时已把管道预埋在地板管道或墙体管道,管道内有牵引电缆线的钢丝或铁丝,如果没有,就用小型穿线器牵引安装人员只需索取管道图纸来了解布线管道系统,确定布线路由管道一般从配线间或走廊水平主干槽道预埋到信息插座安装孔,安装人员只要将4对线电缆线固定在信息插座的拉线端,从管道的另一端将线牵引拉出
(2)天花板内布线水平布线最常用的方法是在天花板内布线,其施工步骤如下1 确定布线路由2 沿着所设计的路由,打开天花板,用双手推开每块镶板,多条4对线很重,为了减轻压在吊顶上的压力,可使用J形钩、吊索和其他支撑物来支撑3 以同一工作信息点为一组,每组布放6根双绞线为宜4 加标签在箱上或放线记录表上写标识编号,在缆线的末端注上标识编号5 从离电信间最远的一端开始布线,拉到电信间6 将线缆整理进机柜
(3)墙壁线槽布线墙面线槽布线是一种明铺方式,均为短距离段落如已建成的建筑物中没有暗敷管槽时,只能采用明敷线槽或将线缆直接敷设,在施工中应尽量把线缆固定咋隐蔽的装饰线或不易被接触的地方,以保证线缆安全在墙壁上布线一般遵循下列步骤1 确定布线路由2 沿着所设计的路由放线3 线槽每隔1m要安装固定螺钉4 布线时线槽容量为70%5 盖塑料槽盖槽盖应错位盖
(二)端接双绞线
1、端接双绞线缆的基本要求双绞线端接是综合布线系统工程最为关键的步骤,它包括配线接续设备(设备间、配线间)和通信引出端(工作区)处的安装施工综合布线系统的故障绝大部分出现在连接之处,故障会导致线路不通和衰减、串扰、回波损耗等电气指标不合格故障不仅出现在某个连接点,也包含链接安装时不规范作业如弯曲半径过小、开绞距离过长等引起的故障所以,安装和维护综合布线的人员,必须先进行严格培训,掌握安装技能1).端接双绞线缆时,必须核对线缆标识内容是否正确2).线缆终接不能有接头
3.线缆终接处必须牢固、接触良好
4.双绞电缆与连接器件连接应认准线号、线位色标,不得颠倒和错接
5.端接时,每对对绞线应保持扭绞状态,线缆拨除外护套长度够端接即可最大暴露双绞线长度为40-50mm扭绞松开长度对于3类电缆不应大于75mm;对于5类电缆不应大于13mm;对于6类电缆应尽量保持扭绞状态,减小扭绞松开长度;7类布线系统采用非RJ45方式连接时,连接图应符合相关标准规定
6.虽然线缆路由中允许转弯,但端接安装中尽量避免不必要的转弯,绝大多数的安装要求少于3个九十度转弯,在一个信息插座盒中允许有少数电缆的转弯及短的(30cm)盘圈安装时要避免下列情况避免弯曲超过九十度;避免过紧地缠绕线缆;避免损伤线缆的外皮;剥去外皮时避免伤及双绞线绝缘层
7.线缆剥掉塑料外套后,双绞线对在端接时的注意事项(课本171图5-22)
8.线缆终端方法应采用卡接方式,施工中不宜用力过猛,以免造成接续模块受损连接顺序应按线缆的统一色标排列,在模块中连接后的多余线头必须清除干净,以免留有后患
9.对通信引出端内部连接件进行检查,做好固定线的连接,以保证电气连接的完整牢靠如连接不当,有可能增加链路衰减和近段串扰
10.线对屏蔽和电缆护套屏蔽层在和模块的屏蔽罩进行连接时,应保证360度的接触,而且接触长度不应小于10mm,以保证屏蔽层的导通性能电缆连接以后应将电缆进行整理,并核对接线是否正确,对不同的屏蔽对绞线或屏蔽电缆,屏蔽层应采用不同的端接方法应对编织层或金属箔与汇流导线进行有效的端接
11.信息模块/RJ连接头与双绞线端接T568A或T568B两种结构,但在同一个综合布线工程中,两者不应混合使用
12.各种线缆和接插件必须接触良好、连接正确、标志清楚跳线选用的类型和品种均应符合系统设计要求跳线可以设计分为以下几种两端均为110插头;两端均为RJ45插头;一端为RJ45,一端为110插头
2.端接RJ45连接头技术人员要制作跳线,即将双绞线连接至RJ45水晶头RJ45水晶头有金属触片和塑料外壳构成,端接水晶头时,要注意它的引脚次序,当金属片朝上时,1~8的引脚次序应从左往右数连接水晶头虽然简单,但它是影响通信质量的非常重要的因素开绞过长会影响近端串扰指标;压接不稳会引起通信的时断时续;剥线时损伤线对线芯会引起短路、短路等故障RJ45水晶头连接按T568A和T568B排序T568A的线序是白绿、绿、白橙、蓝、白蓝、橙、白综、棕T568B的线序是白橙、橙、白绿、蓝、白蓝、绿、白综、棕下面以T568B标准为例,介绍RJ45水晶头连接步骤1 剥线用双绞线剥线器将双绞线塑料外皮剥去2到3cm2 排线将绿色线对与蓝色线对放在中间位置,而橙色线对与棕色线对放在靠外的位置,形成一橙、左二蓝、左三绿、左四棕的线对次序3 理线小心地将剥开每一线对,并将线芯按T568B标准排序,特别是要将白绿线芯从蓝和蓝白线对上交叉至3号位置,将线芯拉直压平、挤紧理顺4 剪切将裸露出的双绞线芯用压线钳、剪刀、斜口钳等工具整齐地剪切,只剩下约13mm的长度5 插入一手以拇指和中指捏住水晶头,并用食指抵住,水晶头的方向是金属引脚朝上、弹片朝下另一只手捏住双绞线,用力缓缓将双绞线8条导线依序插入水晶头,并一直插到凹槽顶端6 检查检查水晶头正面,查看线芯是否正确;检查水晶头顶部,查看8根线芯是否都顶到顶部7 压接确认无误后,将RJ45水晶头推入压线钳家夹槽后,用力捏紧压线钳,将突出在外面的针脚全部压人RJ45水晶头内,RJ45水晶头连接完成
4.
3.1双绞线电缆牵引当同时布放的线缆数量较多时,就要采用线缆牵引,线缆牵引就是用一条拉绳或一条软钢丝绳将线缆牵引穿过墙壁管路、天花板和地板管路牵引拉绳与线缆的连接点应尽量平衡,所以要采用电工胶带紧紧地缠绕在连接点外面,以保证平滑和牢固拉绳在电缆上固定的方法有拉环、牵引夹和直接将拉绳系在电缆上3种方式;拉环是将电缆的导线弯成一个环,导线通过带子束在一起然后束在电缆护套上,拉环可以使所有电缆线对和电缆护套均匀受力牵引夹是一个灵活的网夹设备,可以套在电缆护套上,网夹系在拉绳上然后用带子束住,牵引夹的另一端固定在电缆护套上,当拉在拉绳上加力时,牵引夹可以将力传到电缆护套上,在牵引大型电缆时,还有一种旋转拉环的方式,旋转环是一种在用拉绳牵引时可以旋转的设备,在将干线电缆安装在电缆通道内时,旋转环可防止拉绳和干线电缆的扭绞,干线电缆的线对在受力时会导致电缆性能下降,干线电缆如果扭绞,电缆线对可能会断裂尽可能保持电缆的结构是敷设双绞线时的基本原则,如果是少量电缆,可以再很长的距离上保持线对的几何结构;如果是大量捆扎在一起的电缆,可能会产生挤压变形
4.
3.2信息插座端接
1.信息点位置的确定与施工1)每一个工作区信息插座模块(电、光)数量不宜少于2个,并满足各种业务的需求2).底盒数量应以插座和盒面设置的开口数来确定,每一个底盒支持安装的信息点数量不宜大于2个3).光纤信息插座模块安装的底盒大小应充分考虑到水平光缆(2芯或4芯)终接的光缆盘留空间的满足光缆对弯曲半径的要求4).安装在地面上的信息插座模块应采用防水和抗压的接线盒
5.安装在墙面或柱子上的信息插座模块的底部离地面的高度为宜300mm.
2.信息模块安装要求在综合布线工程中,安装信息插座要做到一样高、平、稳定信息插座中有信息模块信息模块压接时一般有两种体式格式
1.用打线对象压接
2.不消打线对象,直接压接
3.按照工程中的经验,一般采取打线对象压接模块模块压接的具体操纵步调如下1)应用剥线对象,在距线缆末尾5cm处剥除线缆的外皮2)剪除线缆的抗拉线3)按色标次序将4个线对分别插入模块的各个槽位内4)应用打线对象对各线对打线,与插槽连接5)信息模块的压接分EIA/TLA568A和EIA/TIA568B两种体式格式6)信息插座模块、多用户信息插座、集合点配线模块安装位置和高度应符合设计要求7)安装在活动地板内或地面上时,应固定在接线盒内,插座面板采用直立和水平等形式;接线盒盖可开启,并应具有防水、防尘、抗压功能接线盒盖面应与地面齐平8)信息插座底盒同时安装信息插座模块和电源插座时,间距及采取的防护措施应符合设计要求9)信息插座模块明装底盒的固定方法根据施工现场条件而定10)固定螺丝需拧紧,不应产生松动现象11)工作区内终接光缆的光纤连接器件及适配器安装底盒应具有足够的空间,并应符合设计要求
5.
3.3配线架端接利用打线器对配线架端接接线
4.4光缆施工相关知识
(一)敷设光缆工具准备参见敷设双绞线的工具准备
(2)光线连接工具准备
1.开缆工具开缆工具的功能是剥离光缆的外护套,有沿线缆走向纵向剥窃和横向剥切光缆外护套两种开缆方式,因此有不同种类的开缆工具,以下是几种典型开缆工具
(1)横向开缆刀
(2)纵向开缆刀
(3)横、纵向综合开缆刀,这是一款摇把式横、纵综合开缆刀,踏实针对光缆施工中剥开光缆外护套而专门设计的,很好地解决了开剥光缆操作中的难点
(4)钢丝钳
2.光纤剥离钳光纤剥离钳用于剥离光纤涂层覆盖和外护层,它的种类很多
3.光纤剪刀光纤剪刀用于修剪凯夫拉线这是一种防滑锯齿剪刀,复位弹簧可提高剪切速度,它只可剪光纤线的Kevlar层,而不是剪光纤内芯线玻璃层或作为剥皮之用
4.光纤连接器压接钳光纤连接器压接钳用于压接FC、SC和ST连接器
5.光纤切割工具光纤切割工具用于多模和单模光纤的切割,包括通用光纤切割工具和光纤切割笔其中,通用光纤切割工具用于光纤的精密切割
6.单芯光纤熔接机单芯光纤熔接机采用芯对芯标准系统进行快速、全自动熔接,它配有双摄像头和5英寸高清晰度彩色显示器,能进行x、y轴同步观察能够进行自动光纤类别识别,自动校准熔接位置,自动选择最佳熔接方式,自动推算接续损耗实施过程
(1)敷设光缆
1.敷设前准备1)工程所用的光缆规格、型号、数量应符合设计的规定和合同要求2)光纤所附标记、标签内容应齐全和清晰3)光缆外护套需完整无损,光缆应有出厂质量检验合格证4)光缆开盘后应先检查各项端头封装是否良好光缆外包装或光缆护套如有损伤,应对该盘光缆进行光纤性能指标测试,如有断纤,应进行处理,待检查合格才允许使用光纤见检查完毕,光缆端头应密封固定,恢复外包装5)光纤衰减系数和光纤长度检验
2.敷设光缆的基本要求1)由于光纤的线芯是石英玻璃,光纤是由光传输的,因此光缆笔双绞线有更高的弯曲半径要求,2芯或者4芯水平光缆的弯曲半径应大于25mm;其他芯数的水平光缆、主干光缆和室外光缆的弯曲半径应至少为光缆外径的10倍2)光纤是抗拉强度比电缆小,因此在操作时,不允许超过各类型光缆的抗拉强度敷设光缆的牵引力一般应小于允许张力的80%,对光缆的瞬间最大牵引力不能超过允许张力为了满足对弯曲半径和抗拉强度的要求,在施工中应使光缆卷轴转动,以便拉出光缆放线总是从卷轴的顶部去牵引光缆而且应缓慢而平缓地牵引,而不是急促地抽拉光缆3)涂有塑料涂覆层的光纤吸乳毛发,而且光纤表面的微小伤痕都将使耐张力显著地恶化另外,当光纤受到不均匀的侧面压力时,光纤损耗将明显增大,因此,敷设时应控制光缆的敷设张力,避免使光纤受到过度的外力在敷设光缆施工中,严禁光缆打小圈及弯折、扭曲,光缆施工宜采用“前走后跟,”的放缆方法,以有效地防止打背扣的发生4)光缆布放应有冗余,光缆布放路有宜盘留,预留长度宜为3~5m在设备间和电信间,多余光缆盘成圆来存放,光缆盘曲的弯曲半径也应至少为光缆外径的10倍,预留长度宜为3到5m有特殊要求的应按设计要求预留长度5)敷设光缆的两端应贴上标签,以表明起始位置和终端位置6)光缆与建筑物内其他管线应保持一定间距,最小净距符合规定7)必须在施工前对光缆的端别予以判定并确定AB端,A端是网络枢纽的方向,B端是用户一侧敷设光缆的端别应方向一致,不得时端别排列混乱8)光缆不论在建筑物内或建筑群间敷设,应单独占有管道管孔,如利用原有管道或与铜芯导线电缆共管时,应在管孔中穿放塑料子管,塑料子管的内径应为光缆外径的
1.5倍以上在建筑物内光缆与其他弱点系统平行敷设时,应有间距分开敷设,并固定绑扎当4芯光缆在建筑内采用暗管敷设时,管道的截面利用率应为25%到30%9)必须在施工前对光缆的端别予以判定并确定A、B端,不得使端别排列混乱根据运到施工现场的光缆情况,结合工程实际,合理配盘光纤的接续人员必须经过严格培训,取得合格证明才准上岗操作在装卸光缆盘作业时,应使用叉车或吊车,如采用跳板时,应小心细致,严禁将光缆盘从车上直接推落到地10)光缆如采用机械牵引,牵引力应用拉力计监视,不得大于规定值光缆出盘处要保持松弛的弧度,并留有缓冲的余量,又不宜过多,避免光缆出现背扣、扭转或小圈光缆应单独占用管道管孔,如利用原有管道和铜缆合用时,应在管孔中穿放塑料子管,塑料子管的内径应为光缆外径的
1.5倍,光缆在塑料子管中敷设,不应与铜缆合用同一管孔采用吹光纤系统时,应根据穿放光纤的客观环境、光纤芯数、光纤长度、光纤弯曲次数及管径粗细等因素,决定压缩空气机的大小,选用吹光纤机等相应设备以及施工方法
4.
4.1光缆传输通道施工
1.管道光缆敷设时,应注意以下要求1).敷设光缆前,应逐段将管孔清刷干净和试通清扫时应用专门的清刷工具,清扫后应用试通棒试通检查合格,才可穿放光缆如采用塑料子管,要求对塑料子管的材质,规格,盘长进行检查均应符合设计规格一般,塑料子管的内径应为光缆外径的
1.5倍以上一个90mm管孔中布放两根以上的子管时,其子管等效总外径不宜大于管孔内径的85%2).当穿放塑料子管时,其敷设方法与敷设光缆基本相同如果采用多孔塑料管可免去对子管的敷设要求3).光缆采用人工牵引时,每个人孔或手孔应有人值守帮助牵引,人工牵引可采用项目无中介绍的玻璃纤维穿线器;机械布放光缆时不需每个孔均有人,但在拐弯处应有人照看4).光缆一次牵引长度一般不大于1000m超长距离时,应将光缆盘成倒8字形分段牵引或在中间适当地点增加辅助牵引,以减少光缆张力,提高施工效率5).为了在牵引过程中保护光缆外套等不受损伤,在光缆穿入管孔或管道拐弯处与其他障碍物有交叉时,应采用导引装置或喇叭口保护管等保护此外,根据需要可在光缆四周加涂中性润滑剂等材料,以减少牵引光缆时的摩擦阻力6).敷设光缆后,应逐个在人孔或手孔中将光缆放置在规定的托板上,并留有适当余量,避免光缆过于绷紧人孔或手孔中光缆需要接续时,其预留长度应符合表22的规定在设计中如有要求特殊预留的长度,应按规定妥善安置敷设光缆方式自然弯曲增加长度/m/km人手孔内弯曲增加长度/{m/(人)孔}接续每侧预留长度/m设备每侧预留长度/m备注管道
50.5~
1.06~810~20其他预留按设计要求,管道或直埋光缆引上架空时,其引上地面部分每处增加6~8m直埋7表227).光缆管道中间的管孔不得有接头当光缆在人孔中没有接头时,要求光缆弯曲放置在电缆托板上固定绑扎,不得在人孔中间直接通过,否则既影响今后施工和维护,又增加对光缆损害的机会8).光缆与其接头在人孔或手孔中,均应放在人孔或手孔铁架的电缆托板上予以固定绑扎,并按设计要求采取保护措施保护材料和采用蛇形软管或软塑料等管材9).光缆在人孔或手孔中应注意以下几点光缆穿放的管孔出口应封堵严密,以防水分或杂物进入管内;光缆及其接续应有识别标志,光缆型号和规格等;在严寒地区应按设计要求采取防冻措施,以防光缆受冻损伤;如光缆有可能被碰损伤时,应在其上采取保护措施
4.
4.2光缆的连接要求光纤接续损耗值应符合设计要求和表中的规定光纤类别和光纤损耗多模光纤接续损耗(dB)单模光纤接接续损耗(dB)平均值最大值平均值最大值光纤接续方法熔接法
0.
150.
300.
150.30机械接续法
0.
150.
300.
200.
304.
4.3光纤端接、盘纤要求1光缆终端接头或设备的布置应合理有序,安装位置需安全稳定,其附近不应有可能损害外界设施,例如热源和易燃物质2从光纤终端接头引出的光纤尾纤或单芯光缆的光纤所带的连接器应按设计要求插入光配线架上的连接部件,暂时不用的连接器不插接,但应套上塑料帽,以保证其不受污染,便于今后连接3在机架或设备内,应对光纤和光纤接头加以保护,光纤盘绕方向要一致,要有足够的空间和符合规定的曲率半径4光缆中的金属屏蔽层、金属加强芯和金属铠装层均应按设计要求,采取终端连接和接地,并应检查和测试其是否符合标准规定,如有问题必须补救纠正5光缆传输系统中的光纤连接器在插入适配器或耦合器前,应用丙醇酒精棉签擦拭连接器插头和适配器内部,清洁干净才能插接,插接必须紧密、牢固可靠6光纤终端连接处均应设有醒目标志,其标志内容应正确无误、清楚完整
4.
5.综合布线子系统施工注意事项对于广大工程技术人员而言,提高综合布线接地系统的稳定性和可靠性将是一项长期而艰巨的任务,那么应该了解在进行综合布线系统的接地设计时应注重的问题
1.综合布线系统采用屏蔽措施时,所有屏蔽层应保持连续性,并应注重保证导线间相对位置不变屏蔽层的配线设备FD或BD端应接地,用户终端设备端视具体情况直接地,两端的接地应尽量连接至同一接地体当接地系统中存在两个,不同的接地体时,其接地电位差应不大于1Vr.m.S有效值
2.当电缆从建筑物外面进入建筑物内部轻易受到雷击,电源碰地,电源感应电势或地电势上浮等外界因素的影响时,必须采用保护器
3.当线路处于以下任何一种危险环境中时,应对其进行过压过流保护 1雷击引起的危险影响 2工作电压超过250V的电源线路碰地; 3地电势上升到250V以上而引起的电源故障; 4交流50HZ感应电压超过250V.
4.综合布线系统的过压保护宜选用气体放电管保护器因为气体放电管保护器的陶瓷外壳内密封有两个电极,其间有放电间隙,并充有惰性气体当两个电极之间的电位差超过250V交流电压或700V雷电浪涌电压时,气体放电管开始出现电弧,为导体和地电极之间提供了一条导电通路
5.综合布线系统的过流保护宜选用能够自复的保护器由于电缆上可能出现这样或那样的电压,假如连接设备为其提供了对地的低阻通路,则不足以使过压保护器动作,而其产生的电流却可能损坏设备或引起着火例20V电力线可能不足以使过压保护器放电,但有可能产生大电流进入设备内部造成破坏,因此在采用过压保护的同时必须采用过流保护要求采用能自复的过流保护器,主要是为了方便维护
6.布线系统要防潮1)数据布线系统进水,对电缆支持高速数据应用的能力能产生重大影响在某些情况下,已经接近标准规定的链路长度上限的电缆,遇到进水时可能会失效这是因为在电缆变湿时,其绝缘性能会发生变化,会影响阻抗及衰减和回波损耗等相关参数2)人们通常认为,覆盖在标准数据电缆外面的PVC材料是防水的,其实PVC材料是吸湿的标准超五类电缆和六类电缆都采用PVC外套,是为了用于室内设计的,不适宜用于潮湿的环境3)对存在不同程度雾或水的室外环境,设计的电缆都会采取防水措施,如阻水胶带和凝胶填充,这些方法成本高,有时会降低电气性能而且,这些防水凝胶基于石油,存在火灾隐患,不适宜室内使用接续点除外4)进水的影响还取决于水的来源及进水的时间敷设的PVC电缆,中部短期内暴露在少量的干净水中,不会产生任何长期的有害影响;直接敷设在混凝土地板上的低烟雾零卤素电缆,没有使用任何管道或保护措施,只要被水淹没一周,损失风险就会大得多;来自积满灰尘的水泥地板、包含溶解污染物的水则会产生更大的危险5)更换受潮的布线系统耗时巨大、成本高、破坏性强很明显,最好的方法是防止电缆受潮位于高度危险区域的企业在网络设计阶段应考虑受潮的危险,现有的布线网络,也应考虑采取哪些措施6)如果可能,应把电缆悬挂在天花板空间的管道中,这要比地板下布线更能降低受潮的危险通过使用管道,如电缆架,在电缆受潮时可以更快使电缆变干,密封管道则可以更好地防止少量水的浸入如果电缆必须通过地板空间,则应在允许的高度范围内,使电缆盘或电缆架尽可能高出地板平面,因此最好使水管设施远离电缆大量集中的区域,如电信间或设备间,也不要在附近设立厨房或厕所7)布线系统应用时不要把电信间或设备间设在地下室中,特别是在邻近河流时,如果不能实现隔离,那么应考虑使用机架或机柜,或建立堤岸,把水流疏导到影响较小的区域中在电缆受潮时,要采取的措施取决于受到影响的电缆数量、更换成本与不更换电缆的业务损失风险之间的比较等对经毛细管反应通过电缆开端进水的电缆,应直接更换;通过外皮受到严重进水影响的电缆可能也需要更换
4、结论本论文是对厦门海洋职业技术学院公寓楼3号楼和教学楼2号楼进行网络综合布线的进行设计首先通过现场勘查,了解建筑物的实际情况,根据情况设计具体的方案,包括各类信息点的位置选择、接入点的要求、确定适合的FD-BD结构、布线设备的配置、绘制系统结构图、各类材料的选择、施工的要求等等,力求把综合布线系统建设成一个可靠、开放、高带宽、可扩展、并满足楼宇未来发展的布线系统本设计针对建筑物的实际情况及建筑物的用途,设计了较为合理的信息点分置位置,及信息点的数量,并有利于为今后对信息点的改进对于不同的建筑物,根据建筑物的面积、楼层数量、房间数量等,设计了不同的FD-BD结构,这样有利于布线工程简化、节约成本对于产品的选择,本设计都是按设计要求,尽量采用最适合的产品,以达到最好的效果对于施工方面,根据建筑物的位置、周边环境、建筑物本身的结构,采用不同的布线方式,使布线线路更加简便、美观,减少外界因素对线缆造成损坏但是本设计还是存在一些缺陷和不足,对于设备的安装及摆放方面的设计及线缆敷设方面的设计本人觉得还不够完善,但是由于对这方面的知识了解的还不够深入,希望在今后将这方面的知识学习得更透彻,可以将这份设计修改得更加合理完善
六、读书笔记
[1]刘省贤•综合布线技术教程与实训•北京大学出版社•2006年综合布线系统技术出现于20世纪的80年代,当时人们只是想把一个建筑物内的各种仪表、控制信号用一种集中监控设备管理起来,以实现对各种设备的自动或手动控制但由于受当时条件的限制,这种控制系统的传输距离和控制点数日不尽如人意 1984年,首座智能建筑在美国出现后,早期的传统布线系统的不足表现得越来越明显例如各种语音、数据、监控信号各自独立由于各个系统的设计和产品安装分别由不同厂家完成,这样不同厂家的产品不能兼容,这不仅使用户的投资进一步增加,更重要的是使各种网络系统的维护管理变得更加困难因此,人们在吸收传统布线技术优点的基础上,一直在寻求一种规范的、统一的、结构化易于管理的、开放式便于扩充的、高效稳定的、维护和使用费低廉的、健康环保的综合布线系统方案近几年,国内建造的很多建筑都成功地采用了综合布线系统如北京2008奥运场馆的“鸟巢”、“水立方”、中华大厦,上海的博物馆、金茂大厦和浦东上海证券交易大厦,广‘东的国际大厦,深圳的深房广场等,都开创了国内智能建筑的先河在“9·11”恐怖袭击中被摧毁的纽约世界贸易大厦的综合布线系统,更称得上是当今综合布线系统技术走向成熟运用的典范 随着IT产业和社会需求的迅猛发展,网络技术已经广泛地渗透到社会生活的方方面面,它影响着我们的日常生活和工作,起到潜移默化的作用我们需要网络,是因为我们需要广泛的信息我们离不开网络,是因为我们离不开交流在数字化的信息社会中,人们一直梦想着足不出户的办公、消费、学习、娱乐、交流等活动因此,承载着网络信息的各种线缆正像常青藤一样向各个楼宇蔓延为了使延伸的网络线缆不至于造成泛滥而无法控制,人们已经认识到了综合布线系统的重要性
[2]余明辉•综合布线系统的设计施工测试验收与维护•人民邮电出版社•2011年 综合布线系统将所有语音、数据、图像及多媒体业务设备的布线网络组合在一套标准的布线系统上,它以一套由共用配件所组成的单一配线系统,将各个不同制造厂家的各类设备综合在一起,使各设备相互兼容,同时工作,实现综合通信网络、信息网络及控制网络间的信号互连互通应用系统的各种设备终端插头插入综合布线系统的标准插座内,再在设备间和电信间对通信链路进行相应的跳接,就可运行各应用系统了 综合布线系统其开放的结构可以作为各种不同工业产品标准的基准,使得配线系统将具有更大的适用性、灵活性,而且可以利用最低的成本在最小的干扰下对设于工作地点的终端设备重新安排与规划当终端设备的位置需要变动或信息应用系统需要变更时,只需做一些简单的跳线,这项工作就完成了,而不需要再布放新的电缆以及安装新的插座
[3]《建筑与建筑群综合布线系统工程设计规范》(GB/T50311-2007)《建筑与建筑群综合布线系统工程设计规范》(GB/T50311-2007)是目前执行的国家标准新标准的变动都遵循几个主导思想一是和国际标准接轨,以国际标准的技术要求为主,避免造成厂商对标准的一些误导;二是符合国家的法规政策,新标准的编制体现了国家最新的法规政策;三是很多的数据、条款的内容更贴近工程的应用,使用方便,不抽象,更具实用性和可操作性国家标准2007版定义到了最新的F级/7类综合布线系统,在设计和验收标准中分别增加了一条必须严格执行的强制性条文,分别是GB50311—2007中的第
7.
0.9条和GB50312-2007中的第
5.
2.5条,内容都是“当电缆从建筑外部进入建筑物时,应选用适配的信号线路浪涌保护器,信号线路浪涌保护器应符合设计要求”这主要是指通信电缆或园区的大对数电缆引入建筑物时,入口设施或大楼的建筑物配线设备(BD)、建筑群配线设备(CD)外线侧的配线模块应该加装线路的浪涌保护器在目前的综合布线系统产品中,具有保护功能的配线模块,只是指8或10回线连通卡线模块
[5]黎连业•综合布线系统与施工技术•高等教育出版社•2002年自改革开放以来,我国的建筑规模居世界的前列,尤其是智能大厦、智能小区建筑技术的进步,对综合布线系统提出更高、更新的要求,向着集成系统方向发展,弱电工程的建设更显得特别重要弱电工程的设计与施工已经成为现代建筑的重要组成部分所谓“弱电”,就是说它的电压低、电流小、功率小、频率高,应用上主要考虑的问题是信息传输,即信息传输的保真度、速度、广度和可靠性其中有涉及到火灾自动报警系统,火灾自动报警系统是由触发装置、火灾报警装置、火灾警报装置以及具有其它辅助功能装置组成的,它具有能在火灾初期,将燃烧产生的烟雾、热量、火焰等物理量,通过火灾探测器变成电信号,传输到火灾报警控制器,并同时显示出火灾发生的部位、时间等,使人们能够及时发现火灾,并及时采取有效措施,扑灭初期火灾,最大限度的减少因火灾造成的生命和财产的损失,是人们同火灾做斗争的有力工具
[6]福禄克网络学院•布线系统测试工程师认证培训教程•2009年随着我国信息化建设的深入发展,越来越多的政府和企业开始上网,网络得到了前所未有的重视与此同时,网络的建设、维护与更新,需要大量的实用型网络技术人才;特别是高层次的网络管理员、网络架构工程师、网络开发运营工程师、企业信息管理师等相关人才,需求尤为迫切作为业界少数为网管员提供专业维护和认证方案的供应商,美国福禄克网络公司收到不少网管员提出的建议,希望我们能够提供针对于网络维护手段的专业培训美国福禄克网络公司为响应网管员的需求,近日发布两个专业培训课程光缆认证测试工程师CFTT和网络维护和故障诊断CNMT证书培训在每一个培训完成后,福禄克网络都会对学员进行考试通过最后的考试的学员可以成为相应项目的认证工程师CNMT是福禄克网络对电信和企业的系统维护、管理人员,网络规划和系统集成工程师等定制的为期两天的培训课程介绍了网络维护、测试和故障诊断的方法通过理论与实验相结合的方式,对网络维护中出现的典型问题进行分析,学员会学到分析网络的常用重要技术,包括应用和协议分析,流量分析,网络管理技术,网络文档备案和交换机测试等讲师会讲解网络故障现象与原因、网络性能监测以及网络维护方案,覆盖的工具有协议分析仪,网络监测系统,以及常用的网络测试软件工具等,使学员在维护网络方面获得实用和直接的知识通过本课程可以增加经验,总结方法,提高快速解决问题的能力
[7]安顺合•智能建筑施工与验收手册•中国建筑工业出版社•2006年建筑设备监控系统应对空调系统进行温湿度及新风量自动控制、预定时间表自动启停、节能优化控制等控制功能进行检测应着重检测系统测控点温度、相对湿度、压差和压力等与被控设备风机、风阀、加湿器及电动阀门等的控制稳定性、响应时间和控制效果,并检测设备联锁控制和故障报警的正确性检测数量为每类机组按总数的20%抽检,且不得少于5台,每类机组不足5台时全部检测被检测机组全部符合设计要求为检测合格
2.变配电系统功能检测建筑设备监控系统应对变配电系统的电气参数和电气设备工作状态进行监测,检测时应利用工作站资料读取和现场测量的方法对电压、电流、有功无功功率、功率因子、用电量等各项参数的测量和记录进行准确性和真实性检查,显示的电力负荷及上述各参数的动态图形能比较准确地反映参数变化情况,并对报警信号进行验证检测方法为抽检,抽检数量按每类参数抽20%,且数量不得少于20点,数量少于20点时全部检测被检参数合格率100%时为检测合格对高低压配电柜的运行状态、电力变压器的温度、应急发电机组的工作状态、储油罐的液位、蓄电池组及充电设备的工作状态、不间断电源的工作状态等参数进行检测时,应全部检测,合格率100%时为检测合格
3.公共照明系统功能检测建筑设备监控系统应对公共照明设备公共区域、过道、园区和景观进行监控,应以光照度、时间表等为控制依据,设置程控灯组的开关,检测时应检查控制动作的正确性;并检查其手动开关功能
[7]雷锐生•综合布线系统方案设计•西安电子科技大学出版社•2004年综合布线系统是网络通信的传输系统,是建筑物或建筑群内信息传递的媒介,它将话音和数据通信设备、交换设备和其他信息管理系统彼此相连,表现了灵活性、兼容性和可靠性等特点综合布线工程也是IT业界和建筑业界共有的一项方兴未艾的可持续发展的信息基础产业综合布线是一种预布线,除满足目前的通信需求,还能满足未来一段时间内的需求设计时信息点数量裕量的考虑,满足了未来信息应用系统数量、种类的增加,采用5E类和6类布线产品能满足未来1Gbit/s到桌面的应用需求,若采用6A则可以达到10Gbit/s在确定建筑物或建筑群的功能与需求以后,规划能适应智能化发展要求的相应的综合布线系统设施和预埋管线,可以防止今后增设或改造时造成工程的复杂性和费用的浪费 综合布线系统实现了综合通信网络、信息网络及控制网络间信号的互连互通智能建筑智能化建设中,楼控设备、监控、出人口控制等系统的设备在提供满足TCP/IP协议接口时,使用综合布线系统作为信息的传输介质,为大楼的集中监测、控制与管理打下了良好的基础
[8]信息产业部•综合布线工程验收规范(GB50312——2007)•中国计划出版社•2007信息化应用系统
1.信息化应用系统的功能应符合下列要求
1.应提供快捷、有效的业务信息运行的功能
2.应具有完善的业务支持辅助的功能
2.信息化应用系统宜包括工作业务应用系统、物业运营管理系统、公共服务管理系统、公众信息服务系统、智能卡应用系统和信息网络安全管理系统等其他业务功能所需要的应用系统
3.工作业务应用系统应满足该建筑物所承担的具体工作职能及工作性质的基本功能
4.物业运营管理系统应对建筑物内各类设施的资料、数据、运行和维护进行管理
5.公共服务管理系统应具有进行各类公共服务的计费管理、电子账务和人员管理等功能
6.公众信息服务系统应具有集合各类共用及业务信息的接入、采集、分类和汇总的功能,并建立数据资源库,向建筑物内公众提供信息检索、查询、发布和导引等功能
7.智能卡应用系统宜具有作为识别身份、门钥、重要信息系统密钥,并具有各类其他服务、消费等计费和票务管理、资料借阅、物品寄存、会议签到和访客管理等管理功能
8.信息网络安全管理系统应确保信息网络的运行保障和信息安全。