还剩28页未读,继续阅读
本资源只提供10页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
文本内容:
一、空调基础与制冷原理
一、空调基础湿空气的性质
1、在大气层中有大量的地表水分蒸发成水蒸气进入大气,形成干空气和水蒸气的混合物,称为湿空气,简称空气其温度越高,饱和水蒸气压力越大,说明该空气能容纳的水蒸气数量越多,反之亦然空气中水蒸气含量一般很少,空气温度往往高于水蒸气分压下的饱和温度,通常水蒸气处于过热状态而在空气调节中常用的空气状态参数有压力、温度、含湿量、相对湿度、比焓、密度等
1.1压力P湿空气由干空气和水蒸气混合而成,其总压力P为干空气分压力Pg与水蒸气分压力Ps之和P=Pg+Ps
1.2温度T、湿球温度Twb和露点温度Tdp温度是表示物质冷热程度的指标,对于混合气体,湿空气的温度也就是干空气和水蒸气的温度,一般用摄氏度ToC表示,有时也用热力学温度TK表示
1.3湿球温度Twb是在定压绝热条件下,空气与水直接接触达到稳定热湿平衡的绝热饱和温度,也称为热力学湿球温度
1.4露点湿度Tdp是指湿空气在含湿量不变的条件下,湿空气达到饱和时的温度当湿空气温度降低其露点温度时产生结露
2、含湿量d含湿量d指1kg干空气所含水蒸气质量,取决于水蒸气分压力Ps,水蒸气分压力越大,含湿量也越大
3、相对湿度Φ相对湿度Φ是指空气中水蒸气分压力Ps与同温度下饱和水蒸气分压力Ps·b之比
4、比焓ρC湿空气的比焓是指1kg干空气的比焓和水蒸气比焓的总和
5、密度ρ空气密度指单位体积空气的质量,单位为kg/m3湿空气密度为干空气与水蒸气密度之和
二、理论制冷循环单级蒸气压缩制冷系统的理论制冷循环在压焓图上如图1-1所示,循环路线是由两条等压线、一条等熵线和一条等焓线组成制冷剂在压缩机中的压缩过程为可逆等熵过程;制冷剂离开蒸发器的状态和压缩机的吸气状态均为饱和蒸气,制冷剂离开冷凝器和节流前的状态均为饱和液体图1-1上1点表示压缩机的吸气状态,它位于蒸发温度te对应的蒸发压力Pe的等压线和饱和蒸气的交点上过程线1-2表示制冷剂在压缩机中的等熵压缩过程,点2可由通过点1的等熵线和冷凝温度TC对应的冷凝压力PC的等压线的交点来确定点2处于过热蒸气状态点3表示制冷剂出冷凝器时的状态,也是进节流阀时的状态它是冷凝压力PC对应的饱和液体,位于等压线PC与饱和液体线的交点过程线2-2’-3表示制冷剂在冷凝器内冷却(2-2’)和冷凝(2’-3)过程点4表示制冷剂出节流阀的状态过程线3-4表示制冷剂通过节流阀的节流过程由于节流前后制冷剂的比焓不变点4是过点3的等焓线和等压线Pe的交点由于节流过程为不可逆过程,所以过程3-4往往用虚线表示过程线4-1表示制冷剂在蒸发器中的气化过程,制冷剂吸取被冷却物体的热量而不断气化,制冷剂的状态沿等压线Pe向干度增大的方向进行,直到全部变成饱和蒸气为止这样,制冷剂的状态又重新回到进入压缩机前的状态,从而完成了一个理论制冷循环
三、实际制冷循环事实上,家用__空调的实际制冷循环不可避免与理论制冷循环之间存在许差别,如流动阻力、换热温差、压缩机偏离等熵压缩、冷凝器中有制冷剂过冷、蒸发器中有制冷剂过热、制热剂液体管和气体管间有回热等情况这些差别将对制冷循环性能产生不同的影响
1、液体过冷对循环性能的影响在实际循环中,饱和液体在冷凝器和节流阀之间的管路流动时,会因流动阻力引起的压力降低使制冷剂部分气化,这种现象将影响节流阀工作的稳定性,因此需要液态制冷剂进入节流阀前有一定的过冷具有液态过冷的循环如图1-2所示图中1-2-3-4-1表示理论制冷循环,1-2-3-3’-4’-1表示过冷循环其中3-3’表示液态制冷剂的过冷过程温度差△tsc=t3-t3’称为过冷度过冷循环的单位制冷量比理论循环有所增加,而单位压缩功不变,因而提高了整个循环制冷系数2.吸气过热对循环性能的影响实际循环中,蒸发器的出口和压缩机的吸气通常控制在过热状态具有吸气过热的循环如图1-2中1’-2’-2-3-4-1-1’所示其中1-1’为制冷剂的过热过程,过热度△tsh=t1’-t1如果是这部分过热发生在蒸发器过程中称为“有效过热”,如果发生在吸气管路中,散失在大气环境中称为“无效过热”“无效过热”制冷循环与理论循环相比,循环单位功增大、单位制冷量不变、单位冷凝热增大、循环的单位体积制冷量下降、制冷系数下降、压缩机的排气温度升高“有效过热”制冷循环与理论循环相比,单位制冷量增大、单位功增大、单位冷凝热增大、单位体积制冷量下降、压缩机的排气温度升高对实际运行的压缩机,希望吸入的蒸气具有一定的过热度,否则压缩机就有可能吸入未蒸发的制冷剂液滴而引起压缩机冲缸现象对于R22制冷系统通常希望有5-10℃的过热度
3、回热循环在系统中增加一个气液换热器,使节流前的液态制冷剂和从蒸发器出来的低温制冷剂蒸气进行内部热交换,使制冷剂液体过冷,低温蒸气过热,这样的循环称为回热循环家用__空调制冷系统中的制冷剂的液体管和气体管绑扎一起可起回热作用图2-1示出了具有回热循环的系统图,而图2-1中1-1’2’-2-3-3’-4’-4-1即为回热循环,1-1’和3-3’表示在回热器中的回热过程在没有冷量损失的情况下,液体制冷剂放出的热量应等于蒸气所吸收的热量
4、压缩机效率对循环性能的影响实际制冷循环中,由于气体制冷剂在压缩机内部的热交换和流动阻力等一系列损失,造成压缩机的输气量下降、耗功量增加、压缩终了制冷剂温度提高,从而使循环性能下降通常压缩机中的不可逆损失约占系统中不可逆损失的30%-40%
5、热交换和压力损失对循环性能的影响1吸气管道从蒸发器出口到压缩机入口之间称为吸气管道吸气管道中的热交换及压力损失直接影响到压缩机的吸气状态热交换和压力降使压缩机吸气比体积增大、制冷系数下降在实际工程中,可以通过减小制冷剂的流速的方法降低阻力、但为了确保润滑油能顺利返回压缩机,这一流速也不能太低2排气管道从压缩机出口到冷凝器入口之间的管道称为排气管道压缩机排气管路向环境散热,可减低冷凝器的热负荷管路的压力降则增加压缩机的压力比,便压缩机的输气系数下降,制冷系数降低3液体管道从冷凝器出口到膨胀阀之间的管路内的制冷剂为液体状态引起管道压力降的因素有管路的流动阻力和液体高度差液体管路的热交换通常是向环境散热,产生过冷效应,使系统制冷量增大管路中的压力降引起部分制冷剂气化,将减少系统制冷量显而易见,冷凝器出口的制冷剂须有一定的过冷度,一般不小于3-5℃4两相管道从节流装置到蒸发器之间的管道中流动着气液两相制冷剂,称之为两相管道通常这一管道的长度很短,而且它引起的压力降对系统的性能几乎没有影响但是对于多个蒸发器共用一个节流阀或一个蒸发器多路蒸发时,则要尽量保证从液体分配器到各个蒸发器之间的阻力相等,否则会出现制冷剂分液不均匀,影响制冷效果5蒸发器蒸发器中阻力对循环性能影响,必须注意到它的比较条件如果假设蒸发器出口的状态不变,为了克服蒸发器中的流动阻力,必须提高制冷剂进入蒸发器的压力,即提高蒸发器的起始温度6冷凝器冷凝器内压力损失都将使压缩机的压力比增大,输气系数减小,降__冷系统的性能冷凝器阻力的存在将减小换热器的传热温差,需要增大换热器的传热__
6、冷凝器温度变化对循环性能的影响假设蒸发温度不变,当冷凝温度升高时,冷凝压力升高,制冷剂的循环量下降,机组的制冷量下降,理论压缩功增大,制冷系数下降;同理,当冷凝温度下降时,机组的制冷量升高,压缩功下降,制冷系数增大
7、蒸发温度变化对循环性能的影响假设冷凝温度不变,当蒸发温度升高时,蒸发压力升高,制冷剂的循环量上升,单位制冷量增大,单位压缩功下降,制冷机的制冷量升高
二、空调机组系统与故障判断分析空调机组涉及到机械、电气、热工、传热、流体等诸多学科领域,热力过程也较复杂有的疑难故障难以立即判断,必须进行全面检查,寻找症状,综合分析,才能准确确定故障,给予排除
一、制冷故障的判断
1、制冷系统故障现象制冷系统发生了故障,一般不可能直接看到故障的部位发生在哪里,也不可能将制冷系统的部件一一分析和解剖,只能从外表检查,找出运行中的反常现象,进行综合分析在检查中一般都通过看、听、摸来来了解系统的运行状况,其中最关键直观的是从制冷系统的高低压力值和各关键部位的温度上反映其运行状态当系统的运行压力和温度超出正常范围时,除了室内、外环境温度恶化外,否则必存在的问题,这是判断故障根源的重要依据
1.1制冷系统压力和温度的检测;制冷系统的压力概念,制冷系统在运行时可分高、低压两部分高压段从压缩机的排气口至节流阀前,这一段称为冷凝压力,也可称为排气压力低压段是指节流阀出口至压缩机的吸气口,这一段称为蒸发压力压缩机的吸气口压力称为吸气压力,吸气压力接近蒸发压力,两者之差就是管路的流动阻力压力损失一般限制在
0.018Mpa以下为方便起见,制冷系统的蒸发压力与冷凝压力都在压缩机的吸、排气口检测即通常称为压缩机的吸、排气压力检测制冷系统的吸、排气压力的目的,是要得到制冷系统的蒸发温度与冷凝温度,以此获得制冷系统的运行状况
1.2制冷系统中的温度概念制冷系统中的温度涉及面较广,有蒸发温度te,吸气温度ts、冷凝温度tc、排气温度td、液体温度等对制冷系统的运行工况起决定作用是蒸发温度te和冷凝温度tc
1.
2.1蒸发温度te是指液体制冷剂在蒸发器内沸腾气化的温度例如空调机组的te为5-7℃作为空调机组的最佳蒸发温度,就是说空调机组的设计te为5-7℃之间,当检修后的空调机组在调试时,若te达不到5-7℃之间,应对膨胀阀进行调整,满足最佳蒸发温度
1.
2.2冷凝温度tc是制冷剂的过热蒸气在冷凝器内放热后凝结为液体时的温度冷凝温度高,其冷凝压力相对升高,它们互相对应冷凝温度超高,机组负荷重,电动机超载,于运行不利,其制冷量相应下降,耗功率上升,应尽量避免
1.
2.3排气温度td是指压缩机排气口的温度(包括排气口接管的温度),排气温度受吸气温度与冷凝温度的影响,吸气温度或冷凝温度升高,排气温度也相应上升,因此要控制吸气温度和冷凝温度,才能稳定排气温度
1.
2.4吸气温度ts是指压缩机吸气口连接管的气体温度,要求控制在ta=15℃左右为好超过此值对制冷效果有一定影响
2、吸气压力变化对制冷系统的影响制冷系统运行时,其吸气压力与蒸发温度及制冷剂的流量有着密切关系对于用膨胀阀的系统而言,吸气压力与膨胀阀的开启度、制冷剂充注量、压缩机的制冷效率、以及制冷负荷大小有关用毛细管的系统,吸气压力与冷凝压力、制冷量,压缩机制冷效率、以及负荷大小有关为此在检查制冷系统时,应在吸气管上装接压力表检测吸气压力对故障分析有重要作用
2.1吸气压力低的因素吸气压力低于正常值,其因素有制冷剂量不足、冷负荷量小、膨胀阀开启小、冷凝压力低(指用毛细管系统),以及过滤器不畅通蒸发不良(内风机坏或室内蒸发器脏)
2.2吸气压力高的因素吸气压力高于正常值,其因素有制冷剂量过多、制冷负荷大、膨胀阀开启度大、冷凝压力高(毛细管系统),以及压缩机效率差等
3、排气(冷凝)压力变化对制冷系统的影响制冷系统运行时,其排气压力与冷凝温度相对应,而冷凝温度与其冷却介质的流量和温度、制冷剂注入量、冷负荷量等有关在检查制冷系统时,应在排气管处装接压力表,检测排气压力,作为分析故障参考
3.1排气压力高的因素当排气压力高于正常值时,一般有冷却介质流量小或冷却介质温度高、制冷剂充注量过多、冷负荷大及膨胀阀开启大等以上因素会引起系统的循环流量增加,冷凝热负荷也相应增加由于热量不能及时全部散出,引起冷凝温度上升,而所能检测到的是排气(冷凝)压力上升在冷却介质流量低或冷却介质温度高的情况下,冷凝器的散热效率降低而使冷凝温度上升对于制冷剂充注量过多的原因,是多余的制冷剂液占据了一部分冷凝管,使冷凝__减少,引起冷凝温度上升
3.2排气压力低的因素排气压力低于正常值,其因素有压缩机效率低、制冷剂量不足、冷负荷小、膨胀阀开度小、过滤器不畅通,包括膨胀阀过滤网以及冷却介质温度低等以上几种因素都会引起系统的制冷剂流量下降、冷凝负荷小,使冷凝温度下降从上述的吸气压力与排气压力变化情况看,两者有密切关系在一般情况下,吸气压力升高,排气压力也相应上升;吸入压力下降,排气压力也相应下降也可从吸气压力表的变化估计排气压力的大致情况
4、吸气温度与排气温度的关系实际上系统的排气温度与吸气温度关系很密切吸气温度升高,排气温度也相对升高,反之则低吸气温度又与系统的制冷剂流量有关系,制冷剂流量大,则吸气温度低,反之则高对毛细管的制冷系统,吸气温度又与制冷剂注入量有关系,制冷剂量多,吸气温度低,反之则高对装膨胀阀的系统,则与阀的开启度有关,开启度大,吸气温度低,反之则高排气温度与冷凝温度有关系,冷凝温度高,排气温度也高,反之则低搞清它们之间关系,就能很好地掌握和控制它们,使制冷系统运行得更好
5、压缩冷凝机组温度变化对制冷系统的影响机组部件的有关温度都有正常的温度范围,超出这个范围就属不正常的态造成这些不正常的因素可能是故障,也可能是调整不正确,但都要分析它的起因,并及时处理或检查可通过测温点直接显示也可用手感来估计
5.1排气温度的影响夏季正常情况下,压缩机的排气温度是比较高的,手无法触摸按国家标准规定R22的制冷系统的排气温度应不超过130oC(一般120oC以下),CMV不超过1150C,超过这温度线属不正常状况排气温度超高的原因,是压缩机的吸气温度超高,或是冷凝温度超高所造成,必须引起注意排气温度超高冷冻油可能结炭,会造成电机绕阻温度过高烧毁压机电机会影响正常工作,轻者使压缩机制冷量下降,重者将使压缩机不能工作当排气温度超过冷冻油的闪点温度时,其冷冻油就可能结炭,影响压机调温排气温度过低,压缩机可能湿行程运行或系统内工质相当少的运行状态压缩机湿行程容易损坏阀结构;制冷剂特少情况运行,会影响电动机的绕阻散热,加速绝缘材料的老化湿压缩可能引起冲缸,功率也很大,电机发热厉害,严重出现堵转现象
5.2机壳温度变化对压缩机和制冷系统的影响,全封闭往复活塞式压缩机机壳外表的温度场合可分两部分第一部分
①上机壳因受吸入蒸气的影响,温度比较低,处处在微热或稍凉范围,约在30℃左右,在吸气管的周围局部机壳表面有结露水的可能
②下机壳因受冷冻油将摩擦热量带出来的影响,其温度比较高,一般在600C以下,机壳内电动机的发热量和被冷冻油带出的摩擦热量,主要由蒸气带出机壳
5.
2.1机壳温度过高的影响及原因,机壳表面温度超过正常值,主要是制冷系统的吸气温度过高,过高的过热蒸气进入压缩机,吸收机壳内热量后,使蒸气的温度更高,从而使机壳的温度上升过热蒸气的温度上升很高,机壳的温度也升得很高,对油的冷却不利,这会影响运动零件的润滑,加速磨损,严重者使轴承抱轴(咬死)另外还会引起排气温度上升
5.
2.2机壳温度过低的影响及原因机壳表面温度低于正常范围,其原因是吸气温度太低它对冷冻油和电动机绕组的冷却有利,但制冷量有所下降当吸气温度特别低时,会使大半只机壳结露,就有液击的危险,这是对压缩机的致命打击,应特别注意同时冷冻油内溶解大量的制冷剂,不利于运动零件的润滑
6、冷凝器的温度状况
6.1空冷冷凝器正常情况下,前半部散热管很热,且其温度有缓慢的逐步下降的趋势后半部散热管的热感程度与前半部相比有较大的降低,这是由于后半部管内制冷剂已逐步液化已达到冷凝温度和过冷温度当不正常情况产生时,一种是前半部不太热,后半部接近常温(环境温度),其原因是压缩机吸入湿蒸气制冷剂或制冷量不足另一种是整个冷凝管都很热,其原因是制冷剂量过多或通风量小,或环境温度高
6.2水冷冷凝器壳管式冷凝器的壳体正常情况是上半部比较热,下半部是温热不正常状况下是整个壳体都不太热,其原因是制冷剂量不够另一种情况是整个壳体都很热,其原因是冷却水量不足或散热效果差(水管内结垢)套管式冷凝器在正常情况下,套管外表面温度从制冷剂入口到制冷剂出口是由热逐步变温不正常情况一种是整个套管外表面很热,其原因是冷却水量太小或散热效果差;另一种是整个套管外表面不太热,其原因是制冷剂量不足
7、贮液器温度状况在正常情况下,贮液器为温热不正常情况下,贮液器表面比较热原因是冷凝器散热不好,冷凝温度高或制冷剂充注量过多(在旁通的情况下贮液器表面有结霜现象)
8、液体管的温度状况在正常情况下,液体管为温热不正常情况下,液体管比较热其原因是冷凝器散热差,冷凝温度高或制冷剂充注量过多
9、过滤器的温度状况基本状况与输液管相同,但它有一个突出的不正常现象,就是过滤器可能会发凉,其原因是过滤网孔也被污泥阻塞,使过滤器不畅通,当制冷剂流过滤网时,发生了节流现象,即有一部分液体会气化吸热,使过滤器发凉,严重的会结露另一种不正常现象是过滤器不热,与环境温度相当,其原因是过滤网完全堵塞不通,制冷剂不能流动
10、吸气管的温度状况正常情况下,吸气管用手摸感觉很凉,并结有露水不正常情况下,一是吸气管较冷、露水太多,以致使机壳大__结露原因是制冷剂流量过大,液体不能在蒸发器内全部气化,有液体回流现象其危害性是压缩机有可能湿行程运行,严重时就会产生液击,阀片受到威胁二是吸气管不凉、不结露、机壳很热其原因是制冷剂流量太小或制冷剂量不足其后果是使排气温度上升,制冷量下降
二、蒸发机组的温度变化对制冷系统的影响
1、热力膨胀阀的外表温度(包括电子膨胀阀)正常情况下,膨胀阀的下半部阀身很凉,并有露水,制冷剂流动声音很沉闷不正常情况下,一是阀体比较冷,表面露水较多,甚至结霜,制冷剂的流动声较大(气体流动)其原因是过滤网堵塞不畅通,或系统内制冷剂量少二是阀体不凉也不结露,听不到制冷剂流动声音,其原因是过滤网堵塞不通
2、毛细管的温度情况正常情况下,毛细管发凉并有结有露水,有液体流动声音不正常情况下,一是表面很凉,也结露,但流动声音较响,是气体流动,其原因是制冷剂不足;二是表面不凉、不结露、听不到流动声音,其原因是滤网堵塞或毛细管堵塞
3、蒸发器温度状况正常情况下,蒸发器外表面很冷,其凝露水珠不断地滴下来,进出风温度较大,通常是△t可在12-14度不正常情况,蒸发器表面不太凉,露水不多,或不结露,可听到制冷剂流动声音很响,进出风温差小其原因是制冷剂量不足,或膨胀阀开启度小
三、环境温度的影响
1、室外机组的环境温度要求按国家标准规定,室外机组在环境温度为35度以下的气温,空调机组应保证正常运行,并能达到产品铭牌所标的制冷量以及其他各项指标当环境温度在35-430C度的范围内,空调机组可以运行,但不能保证其铭牌所标制冷量,它已处于满负荷运行,这时的冷凝温度、压力、排气温度都相当高,若室内热量较大,电控保护器就有可能动作,切断电源,停止运行当室外气温超过43度,空调机组就处在超负荷运行,会导致电控保护装置的动作,进行保护状态、停止运行
2、室内空调气温的要求室内正常恒温值最高就不超过30度为好若在超过30度气温下运行,空调机组有可能处在超负荷工况下运行,制冷系统的冷凝温度和排气温度都会上升,也可能导致电保护器动作,切断电源,对空调机组的运行寿命不利
3、热泵系统与单冷系统情况相同,热泵运行是否正常,主要检查四通换向阀的工作情况换向阀换向时,可听到有比较响的气体流动声以及电磁阀顶针的撞击声,当电磁阀在换向过程中听不到上述两种声音,那电磁阀可能出故障或显示换向阀故障
四、全封闭式压缩机的故障分析全封闭活塞式压缩机发生了故障,由于零配件难以供应,绝大多数情况是更换压缩机,涡旋压缩机更是如此了更换新压缩机应注意以下事项
1、最好是同型号的压缩机,如有困难应选择性能规格相同或接近的压缩机压缩机的主要性能和规格有名义制冷量(相同工况),电动机的电源和容量(电压相数、频率、电流等),以及电容器的电容量
2、外形尺寸应相同或相当,以确保压缩机能装进机组
3、底脚尺寸应相同,若不相同,就要改变机组底盘的底脚尺寸
4、吸排气管的方向与位置应相同或接近若不相同,就要重新安排接管尺寸
5、全封闭活塞式压缩机常见的几种故障及其症状如下制冷效率低压缩机的实际排气量下降,达不到原定制冷量,实际情况就是满足不了原有冷负荷制冷效率低一般由以下四种因素引起
5.1活塞与气缸严重磨损(包括转子式压缩机)
5.2气缸盖垫片中盘破裂,形成高低压腔短路
5.3气阀严重泄漏(包括转子式)
5.4机壳内排气管断裂(往__)以上四种情况所表现出的症状是,排气压力下降,吸气压力升高,吸、排气压力差较小或很小,机壳有不同程度的发热,有的排气管烫手
五、压缩机不能运转当接通压缩机电源时,只听到机壳内电动机有“嗡嗡”的声音,但不运转,约过3-5s时间,热保护器起跳,切断电源这种症状是由以下几种故障引起的1主轴颈与轴承,或连杆大头与曲柄销因断油而已烧熔(俗称咬死),其原因是压缩机内少油或油孔堵塞2气阀损坏,破碎的阀零件落进气缸,使活塞不能往复运动3连杆断裂,相互被撑住,电动机拖不动
六、压缩机内的线圈损坏其症状是当通上电源,熔断器熔丝熔断或断路跳闸这种症状存在下列四种故障的可能1电动机的定子绕组烧坏,线圈的电磁线绝缘层烧焦,绝缘被破坏,绕组碰壳2匝间短路电动机定子绕组中部分线圈绝缘击穿,部分线圈碰壳3碰线电动机电源导线绝缘损坏或被动切断而碰壳4定子绕组绝缘层严重老化,但还未烧坏其症状是能运行1-2min,然后也熔断熔丝,断路器跳闸或过流保护器动作保护
七、电气系统的故障分析空调机组的电气控制分为强电线路控制板与电子线路控制板因它们的控制对象有区别,其故障分析分别叙述电器是用来控制和保护制冷系统及风机系统的器件它除了电气线路本身故障外,有相当一部分故障是发生在制冷系统和风机系统上,但其症状却在电气控制线路上反映出来因此在分析电气控制系统故障时,不可避免的要涉及到制冷系统和风机系统的故障问题本节以分析电器故障为中心
1、强电控制系统故障及症状1压缩机和风机不运转当合上开关后压缩机与风机不运转.作为电气线路上的故障有
①电源无电;
②电源插座内断线;
③熔丝熔断(控制线路);
④插头插座接触不良;
⑤电源电压过低,电动机不起动,热保护器起跳,切断电源;
⑥选择开关内部断路;
⑦电气控制线路断路其原因有些是操作不当,或是质量问题,有些是制冷系统和风机系统引起如就熔丝熔断这一点,除了电气线路有碰线,碰壳短路外,也可能是制冷系统中风机系统有故障而引起
2、风机运转但压缩机不运转1温度设定范围高或等于、大于室温2接触器不动作或触头烧蚀3过载保护器触点断开其原因是制冷系统运行中有超负荷现象,使保护触点跳开4压缩机起动电容损坏,或电压波动大5压缩机电动机烧坏
3、空调机组运行后压缩机起停频繁其故障原因如下1设定温度接近室温或温度传感器故障2电源电压不稳定时高时低或三相不平衡3过载保护器的双金属接触不良使电源产生时通时断的情况
4、压缩机__运转不停的故障其原因如下1由于室内发热体多,热量大空调__的热负荷大,空调机组不匹配2控制器触点粘连室内机回风不畅
八、热泵型空调机组不制热空调机组在制冷运行时能够制冷降温,而制热运行时不够制热,这是热泵装置的电磁换向阀或切换开关有故障一般会产生以下几种故障
1、电磁阀的电磁线圈烧坏或断路,其原因是
①曾在恶劣环境下工作;
②线圈电源通、断频繁;
③__在超电压下工作,线圈常处在超温升下工作,使绝缘层老化而击穿
④电磁阀线圈__不到位,或松脱
2、电磁阀的阀心卡住或损坏其原因有
①有油污或杂质进入阀内搁住阀心;
②制造质量差,使用寿命短而损坏
3、换向阀不能换向其原因是多方面的,主要是制冷剂不清洁和制造装配质量有问题,使换向活塞不能运动
4、加热器损坏或无电压提供
九、送风系统故障分析
1、风箱噪声是由风机运行时引起箱体振动或紧固件松动造成
2、风机振动大多由__尺寸不佳,或轴承端缺少润滑脂过度磨损,__不良运行振动大、噪声高、机械磨损严重以及运转抖动造成
3、盘管、表冷器灰尘污垢严重,形成的原因是空气中的灰尘__吸附其表面,加上空气中的油粒混合而成将直接影响制冷热效果,__内空气中的洁静度也会随之下降
4、电动机轴承磨损电动机缺少保养维护,其轴承内润滑脂干燥或油脂皀化失去润滑功能,__运行造成轴承磨损,噪声大,应每年定期进行一次保养
5、风道内有异味风道在__运行后其内壁附着大量杂质加上其它异味串入混合而成在机械方面形成的异味有传动皮带由于磨损而打滑或__皮带轮时不在同__面上偏离磨损,以及电动机线圈老化绝缘下降形成高温而产生
三、通风系统的故障分析通风系统的故障症状表现在三个方面风量下降、电动机故障、运行噪声大现就按这三部分来讨论分析风量下降这里是指风量有明显减小,一般至少要下降20%-30%对分体式空调机组,它有室内机和室外机的二套通风系统,它们对制冷系统的制冷量有密切关系,风量足,制冷量也足风量不足,其制冷量会下降如何判断风量下降,可以通过几种粗略的测量手段可以得出结果;
①测量机组的进出口风的温度差,室内机一般为12-13度,高于13度则其风量为不足症兆另外,其冷凝温度升高可能是冷凝风量不足引起
②用手感觉来辨别风量大小,这要求有丰富经验的积累才可能有一定的准确度总之,风量下降的症状比较难以辨别,这需要不断地实践,积累经验,并结合其他所出现的症状,进行综合分析下面介绍几种引起风量下降的故障现象1传动带打滑2叶轮的紧固螺钉松动3叶轮反转4滤尘网堵塞5冷凝器结灰6)风机转速下降(两器脏引起风量下降时,风机转速上升)
1、电动机故障1轴承严重磨损2电动机绕组烧坏3绕组匝间短路4电动机轴承烧结5电容击穿
2、运行噪声大1)叶轮与风圈相擦2轴承严重磨损3传动带损坏4电动机底座螺栓松动以上的故障分析是按空调机组各个系统的单独叙述从空调机组的整体看,其故障总是从最典型的表面症状表现出来,通过某些检查,得到某些症状后,经综合分析就可判别出哪一类故障因此检查和分析故障只有以直观的表面症状现象入手,再按空调机组的控制和运行规律,深入某系统内部检测,进行综合分析而得出故障部位,排除故障只是操作问题由于各系统的故障会互相影响和互相牵连,因此需要综合分析现按照空调机组通常发生的外表症状划归为几种类型,将每一种类型的故障、特征及排除方法都列成表,以便于工作中查找
四、风水冷冷水机组故障分析
一、这类故障主要发生在风水冷冷水机组系统中制冷系统中有故障,运行不正常,会引起各种电器保护装置起跳,切断电源要检查这类故障,首先要检查出哪一种保护器起跳,然后才有方向去查有关部位的故障症状,查出症状经过分析,才可确定故障内容装有电脑板的空调机组,同时又设立了控制运行及监视故障症状的代码在运行中若显示器显示某一故障代码就能知道某部位有故障症状检修人员可有针对性对某部位检查找出症状分析出故障原因本类故障分析见表1-1表1-1故障内容简要分析排除方法1)制冷剂量不足1)吸气压力过低、节流器流动声大(气流声)、吸气管不结露1)检漏、补漏加制冷剂2)过滤器阻塞不畅通2)吸气压力过低、节流器流动声大(气流声)、吸气管不结露,过滤器外表面发凉(冷)2)拆下清洗过滤网或更换3)膨胀阀过滤网阻塞不畅通3)吸气压力过低、节流器流动声大(气流声)、吸气管不结露3)拆下过滤网清洗4)膨胀阀的开启度过小,制冷剂流量过小4)吸气压力过低,节流声大,吸气管不结露,阀体下半段结霜4)调大阀门,适度5)制冷剂量过多,部分冷凝管被液体占据5)排气压力过高,吸气管和机壳结露,超载运行,热保护器起跳5)排除部分制冷剂,至吸气管结露为止6)制冷系统混入空气,部分冷凝管被空气占据6)排气压力,排气温度,吸气压力均高,机壳很热,吸气压力电流波动大6)停机,放空气7)风冷冷凝器外表面结灰(翅片之间),水冷冷凝器内结水垢7)风冷冷凝进出风温差大,风量大,冷凝压力高,水冷冷凝进出水温差小,冷凝压力高,外壳热7)清洁风冷冷凝器用刷子刷或空气吹;清洁水冷冷凝器清洗管内水垢8)空调__热量大,处于高温运行(超负荷)8)吸排气压力高,过载使热保护器起跳,回气排气温度高8)制冷量不够,增添空调机9)气阀严重泄露9)吸排气压力差很小,高低压力表抖动厉害,机壳高热,热保护器起跳9)解剖修复或更换压缩机10)冷凝器温度高,进出水温差大10)排气压力和排气温度高,进出水温差大,单位制冷量下降10)除垢或清理进水阀堵塞,开启度过小11)冷却水量调节阀失调,水量低11)水泵出口压力上升,噪音增大,系统排气压力温度声高,高压保护停机11)修复或更换水量调节阀12)冷却水泵排水量严重不足12)排气压力,温度高,单位制冷量下降,冷凝器进水温度高12)查冷却水泵和风机管路截止阀13)冷却塔冷却效果下降13)管路进出水阀门开启度不够,水量小,冷却风机故障,管内有空气13)调大进出水阀门,检查冷却风机,排空阀冷却塔换热效果差14)膨胀阀感温包内工质泄漏,阀门关闭不通,制冷剂不能流动14)吸气压力为真空状态,低压开关保护停机,排气管不热,节流器无流动声,蒸发器无冷风吹出14)更换膨胀阀15风扇、水泵、压缩机皆不能起动1)停电2)电源开关跳脱3)控制回路,电源保险丝断了4)水泵故障,或过流保护1)待电源恢复2)检查后送电3)更换保险丝4)检查水泵故障,确认正常后复位16水泵运转,而压缩机不起动1)温度开关设定温度太高2)温度开关故障3)压缩机过载保护未复归4)暖气开关设定温度太低(暖气用)5)机组保护开关跳脱未复归1)修正温度开关之设定值2)检修或更换3)检查后复归4)修正温度开关之设定值(暖气用)5)检查确认系统无故障后复位17压缩机可运转,但立刻停止1)吸入、吹出风口被挡住2)冷凝器过脏,排气温度高3)地场欠佳,通风不良4)风扇故障5)冷水管路水阀未打开6)冷水量过低7)冷媒泄漏8)压缩机过载保护9设定温度与室内接近10冷却管内有大量空气1)将挡住物移开2)冷凝器3)改善通风条件4)检修或更换5)全开水阀6)检查水泵,并排除水管内空气7)系统检漏,并修复8)检查过载原因,复位9调大温度设定值10确认膨胀水箱__高度和排空阀的好坏18冷气变暖气1)冷气、暖气选择开关切换错误2)四路阀故障1)检查选择开关,并切换至冷气2)更换四路阀及电磁阀19暖气变冷气1)冷气、暖气选择开关切换错误2)四路阀故障1)检查选择开关,并切换至暖气2)更换四路阀及电磁阀20冷却水进出水温差大,低压过低(冷气运转时)1)管路阀位切换错误,管路堵塞2)管路中气体过多1)检查冷却水管管路阀件及配件2)排除管路中之空气21进出水温差大,高压过高(暖气运转时)1)管路阀位切换错误,管路堵塞2)管路中气体过多1)检查水管路阀件及配件2)排除管路中之空气22风量不足,并伴有异味电动机与风机皮带轮的__不在同__面和距离不当,皮带过松调整电动机、风机之间距离适当徒手向下压按调整好的皮带上部__,使其向下__16mm为宜承接上表
二、空调机组在运行中发出不正常噪声和振动空调机组运行时,会产生有规律的运行噪声,但它是比较低和有节奏的,这是不可避免的正常噪声若是发出非常刺耳的声音,这是不正常的噪声,是有故障的噪声若不及时发现和处理,就会损坏机器零件,应予以重视本类故障分析见表2-1表2-1空调机组在运行中发出不正常噪声和振动___位故障内容简要分析排除方法
1.压缩机部分1制冷剂液与油吸入气缸进行液体压缩和排放产生液击现象2系统内制冷剂注入量过多经常引起回液3热力膨胀阀开启度大引起回液4电动机过载发出较响的电磁噪声5轴承磨损较严重电动机转子与定子相磨擦1液体对气阀的冲击声以及产生振动使压缩机产生抖动2排气压力升高,压缩机进气端结霜严重,或超负荷运行3压缩机进排气端温差大,运行声音沉重,有撞击声4压缩机振动较厉害电流较高,有异常响声5)运行声音异常,电机温度高,有磨擦响声或异味1停机几分钟再起动或调整进气阀开度2放出多余部分制冷剂3调小膨胀阀开启度至正常值4开大压缩机排气阀,或关小进气阀门5停机更换轴承,检查定子,转子有无过度磨损
2.整机部分1压缩机与底盘的共振声2室外机组与基础的共振声1压缩机振动厉害引起底盘共振压缩机地脚螺栓旋得过松,无缓冲垫2基础紧固螺栓松动1适当调整压缩机地脚螺栓,加装缓冲垫2旋紧螺栓
3.风机部分1叶轮与风圈的碰撞2电动机轴承严重磨损3传动带损坏4电动机底脚螺栓松动1发出金属磨擦的刺耳声支头螺钉松动叶轮上移位使叶轮与风圈相碰2轴有跳动的振动声,磨擦声3传动带破裂,发出”噼啪”拍打声4电动机跳动厉害并发出震动声1纠正位置拧紧支头螺钉2更换轴承或电动机3更换传动带4调整的位置旋紧螺栓
三、空调机组有气味空调机组内发出难嗅的气味这是故障的预兆症状应进行检查.其故障分析见表2-2表2-2空调机组有异常气味故障分析___位故障内容简要分析排除方法
1.制冷系统部分制冷系统有较大泄漏泄漏的制冷制剂中混合大量冷冻油散发在空气中,严重者可听到泄漏声检漏、补漏添加制冷剂和冷冻油
2.风机部分传动带打滑与带轮槽磨擦产生高热表冷器风箱内壁附有陈年灰尘或回风内夹带异味气体有橡胶臭味,同时还伴有不太高的磨擦声,检查皮带轮__是否偏离同__面2表冷器翅片间或内壁长时间没清洗,和回风口__在有异味源的上方1调紧传动带,损坏的更换,校正两皮带轮的不平度2清洁表冷器和风箱内壁灰尘,清除异味源
3.电气系统部分1)电磁线圈过热,使绝缘层老化2)导线超容量而过热,使绝缘层老化3)插头插座接触不良,发生火花而过热,使塑胶焦化1)有电器烧焦气味,严重者可看到冒烟2)有橡胶或塑料气味,用手摸导线感到烫手3有塑胶烧焦时,插头插座发烫并有异味1)更换烧坏电器2)换上容量大的导线3)修复或更换插座
五、风冷、水冷螺杆冷热水机组故障分析风冷式螺杆冷水机与水冷式螺杆冷水机故障现象,除冷却方式有异外,其它故障症状基本相同在判断螺杆机组故障时应充分考虑相关保护系统,根据故障现象查找故障原因直观且易排除故障在故障原因不明时应仔细检查相连的保护装置是否进入保护状态,根据保护状态再去排除故障有些故障现象一时无__确判断究竟由哪部分造成,可采用分断形式进行,即脱开主负载压缩机、冷却水泵、冷冻水泵或冷却风机,按操作程序操作,检查主回路电源是否到达怀疑的故障部分,若电源到达怀疑的故障部分说明主控制回路正常,二次控制回路也正常,问题出在怀疑的设备上,若操作控制程序不能正常执行则问题出在二次控制回路或检测传感部分只要认真检查并加以判断故障就不难解决,下面综合螺杆机组可能出现的故障现象用列表形式加以分析故障现象简要分析排除方法机组不起动无电压,控制回路保险管断,系统过载保护欠压过压保护检查电源和控制保险管,过载保护器机组能起动,但无__常运行能量调节阀设置位置不当,延时启动时间不够,电机自身故障,过载保护整定值不对或过载保护器故障将能量调节阀设定适当,按说明书要求设定启动延时时间,检查或更换过载保护器起动运行后,马上停机冷却风机风冷或冷却水泵故障,冷却水阀开启过小或滤网堵塞,电机自身故障,设定温度过低,防冻开关保护,传感器故障,冷却管内有大量空气检查风机、水泵、阀门滤网和电机阻值,调高设定温度值,更换传感器,确认膨胀水箱__高度和排空阀的好坏有电源指示,无法启动运行控制回路保险管容断,电压超出允许范围,缺相,过载保护,高低压力开关动作,无水压检查控制回路,测量电源电压,查找缺相,过载原因确认系统和水压正常后复位制冷热量下降能量调节阀设置不当,冷凝器换热效果差,冷冻泵叶轮磨损冷却风机,膨胀阀过滤器阻塞,冷却管内有空气调整能量阀适当,检查冷凝器、冷却泵、冷冻泵、风机、膨胀阀、换向阀过滤器、排空阀运行中停机,且保护装置动作保护系统压力过高或低,缺相,温度设定过低,冷却系统故障,电机过载,无油检查系统压力,调高温度设定值,查找冷却风机或水泵、电机故障,测量压机三相电源,补加冷冻油冷却风机运行风冷热交换差风机转速下降,冷凝器翅片间结灰太多检查风机转速下降原因,清洗传动轴承、冷凝器冷凝器冷却效果差水冷冷凝器管内结有水垢,进水量小,阀门开度不够,冷却水泵叶轮磨损清洗管内水垢,调大进水阀门开度,修复或更换水泵冷却水泵、冷冻水泵不起动无启动控制电压,过载保护,电机故障,泵体内卡住叶轮损坏检查启动和控制电压,查找过载原因,修复或更换泵体冷却风机风冷或冷却水泵运转压缩机不起动高低压压力开关,防冻保护开关,水压压力开关,压机过载保护器动作或坏检查相应保护装置,确认无故障后复位压缩机开停频繁温度设定值接近室温,温度传感故障,膨胀阀坏,防冻开关设置不当,过滤器堵塞调整设定值,检查传感器,膨胀阀、防冻开关,更换过滤器机组运行时噪音过大机组__不当,部份零件松动、碰撞、磨擦、转动件轴承磨损,泵体风叶抖动和磨擦调整设备稳固,紧固松动部件,更换轴承或风叶紧固校正低压停机系统内制冷剂过少或泄漏,过滤器堵塞,膨胀阀坏查漏补充制冷剂,更换过滤器、膨胀阀高压停机冷却风机坏,冷却效果差,冷却水泵坏,壳管内水垢太多,系统内阻力大,回气温度高,冷却水入口堵塞检查风机、水泵、冷却器进水阀和入口过滤网油压低停机压缩机油泵故障,冷冻油低于下限限位,吸入口堵塞修理油泵,添加冷冻油至上限,清洁油底壳及油腔通道油加热器故障加热器坏,接触器不动作或触头烧蚀,无控制电源,传感器坏测量加热器、接触器、控制电源传感器或更换控制程序正常,压缩机不起动接触器触头烧蚀,接触不良,热保护器断开,压缩机故障检查主接触器、过载保护器、压缩机和电源是否缺相压缩机起动后马上停机且过载保护压缩机匝间短路,电源线路松接,轴承或机件卡死测量线间阻值,查找压机电源和轴承、机件传感器故障传感器坏,无传感器电源线路,有开路、断路现象或插接不良检查传感器和电源及线路控制板故障无电源指示或无控制电源,设定无效查__端子有无电压输出或更换代码故障说明间要分析排除方法E01变频器模块故障三相电压过低或过高,压机接线有误,模块故障查压机自身绝缘或用二极管档测量,P、N与相间值正向约为400欧姆,反向为无穷大为正常,电压波动超出正常值E2XX与室内通讯故障通讯线未接如开路、断路或接点,主板或模块板坏,屏蔽网线与地连接检查通讯线的好坏和接线方法,或更换控制板E03交流输入电流采样异常输入电流过低或过高,采样故障、线路板坏、压机阻值不平衡检查电源,更换线路板测量压机值E04缺氟或换向阀故障传感器__有误或开路,断路,换向阀没有换向,缺氟检查传感器和换向阀线圈是否松脱、坏、检查系统压力E05交流输入电流过大停机电压不稳,排气压力大,有堵转现象检查电压和系统压力,压机阻值E06压机排气温度过高(≥115℃)缺氟,膨胀阀开度不够、系统有堵塞现象,压机通风不良,功率过大,少油,功率过小,卸荷不好加氟、检查膨胀阀和系统有无堵塞,冷媒管急弯现象,改善外机环境温度,查看功率匹配及输入电压,加冷冻油E07室外机主板温度传感器测器故障传感器有开路、短路现象、超出测温范围,插接有误,无传感电压检查传感器是否正常和主板温度及传感电源E08压机排气温度传感器故障传感器开路、短路、超出测温范围,插接有误,板坏检查传感器好坏及连接可靠、测量传感电压E09室外盘管中点温度传感器故障超出测温范围、传感器坏、插接有误,板坏检查被测量点温度和传感器E10压缩机吸气温度传感器故障超出测温范围、传感器坏、插接有误、板坏.检查被测量点温度和传感器E11室外环境温度传感器故障超出测温范围、传感器坏、插接有误、板坏检查被测量点温度和传感器,改善环境状况E12室内机总功率过大JP
1、JP2设置与功率不匹配和室内机总功率过大根据室内机功率匹配跳线E13室外机环境温度超温(≥54℃≤-20℃)传感器__有误、坏,外机通风不良,环境温度过高检查传感器,改善通风条件E14直流母线电压采样异常电压波动大,取样不稳;线路板故障功率过大检查电压,查找功率过大原因E15室外机主板温度过高≥68℃散热效果差,环境温度高,传感器坏,板坏清洁散热器,改善通风条件,检查传感器
六、CMV一拖多室外机调试板故障显示分析E16压机外壳温度开关断开(温度过高)压机超温,连接线开路或接触不良、温控坏、系统有堵塞现象、电流大检查超温原因,更换温度开关E17变频器散热器温度传感故障传感器坏、断线,接触不良连接有误、超出测温范围已屏敝检查连接方式和传感器、查找升温原因E18变频散热器温度过高(≥85℃)冷凝效果不好、环境温度高、运行负荷加重,散热不好改善冷凝效果和环境温度、查找升温原因E19吸气压力(低压)开关断开(压力过低)压力开关坏、开路系统泄漏、堵塞检查压力开关和阀开启度查看系统是否漏氟、堵塞.E20排气压力(高压)开关断开(压力过高)冷凝器脏、风机故障、换热效果差、压力开关坏、阀开启度过小、堵塞、室内机功率过小、旁通阀不能开启检查风机、冷却效果、系统状况、压力开关和阀开启度,该冷凝器高压开关是否插得太深E30降频保护状态交流输入电流大、排气温度高、冷中、蒸中温度、回气温度低检查输入电流E60室外机主板记忆内存故障更换E61室外机主板时钟故障更换E62室外机主板程序故障更换E63室外机软件故障更换E64室外机主板内存资料故障更换
七、室内风机盘管线控器故障显示分析代码故障说明简要分析排除方法E01变频器模块保护电源不稳,电机绕组有故障、接线有误,取样电路波动检查电源、压机阻值和接线方法E02室外机交流输入电流过大模块取样异常或功率匹配过大、电源不稳、压机异常检查跳线方法,测量电压和压机阻值E03室外压缩机排气温度过高检查压机,冷凝器通风状况、真空度不够或有堵塞现象、功率匹配过大,系统缺氟,室内功率过小改善压机和冷凝器通风条件,检查系统和跳线方法,卸荷不好E04室外机传感器故障传感器松脱短路、开路、接触不良超出测温范围,无传感器电压提供检查传感器和控制电压E05室外机直流母线电压异常电源波动、取样不准或线路板坏、压机异常检查电压和线路板及压机工作状况E06缺氟或换向阀故障电磁阀线圈可能有松脱,开路现象无控制电压、查室内外盘管传感器有无脱离固定套,漏检查换向阀线圈和传感器__到位,检漏E07室外机交流输入电流采样故障压缩机是否启动或故障电压是否在正常值,压机运行不稳检查电压和压机是否正常连接是否可靠.E08室内机总功率过大控制板JP
1、JP2跳线功率过小或室内机总功率过大按室内机匹配跳线E09室外机没有收到室内机__接点氧化、有开路状况存在接线有误,线控器坏,无电源__检查连接线是否完好正确,查__电源,更换线控器E11室内机与室外机通讯故障连接端氧化、开路和通讯板无电源提供,接线有误或对地检查电源和接线方法,确认线控器好坏E12室温传感器故障传感器松脱、短路、开路、接触不良、无传感电源板坏.检查传感器和控制电压E13室内盘管传感器故障传感器坏、或脱离固定套超出测温范围检查传感器和被检测温度范围E14线控器与室内机通讯故障线路连接不好、开路、无通讯电源屏蔽网线对地.检查__线和电源及屏蔽网线E15细管传感器故障传感器坏、接触不良、脱离固定套固定好传感器或更换E16粗管传感器故障传感器坏、有开路、断路、短路或松脱固定好传感器或更换
八、CMV故障显示分析
1、天花机A、室外机的故障分析故障内容故障显示简要分析排除方法压缩机排气温度过高双色灯绿灯闪亮1次停2秒系统缺氟,膨胀阀开度不够、有堵塞现象,压机通风不良,功率过大,温度传感器故障室内功率过小、少油,卸荷不好加氟、检查膨胀阀和系统有无堵塞,冷媒管急弯现象,改善外机环境温度,查看功率匹配及输入电压缺氟或换向阀故障双色灯绿灯闪亮2次停2秒电磁阀线圈有无松脱,开路现象无控制电压、查室内外盘管传感器有无脱离固定套,漏检查换向阀线圈和传感器是否__到位室外机交流输入电流过大双色灯绿灯闪亮3次停2秒电压不稳,排气压力大,有堵转现象检查电压和系统压力,压机阻值室外机交流输入电流采样异常双色灯绿灯闪亮4次停2秒输入电流过低或过高,采样故障、线路板坏、压机阻值不平衡检查电源,更换线路板、测量压机值室外机直流母线电压异常双色灯绿灯闪亮5次停2秒电压波动大,取样不稳线、路板故障、功率过大,压机异常检查电压,查找功率过大原因和测量压机阻值室內机总功率过大双色灯绿灯闪亮6次停2秒JP
1、JP2设置与功率不匹配和室内机总功率过大根据室内机功率匹配跳线室外机传感器故障双色灯绿灯闪亮7次停2秒传感器松脱短路、开路、接触不良、检测温度超范围,无传感电压提供检查传感器和控制电压室外机变频模块保护故障双色灯绿灯闪亮8次停2秒电源不稳、电机绕组有故障、接线有误,取样电路波动检查电源、压机阻值和接线方法噪声大风机本身噪声大,__时天花板直接与面板或机体连接查风机噪声大原因或轴承、面板、机体和天花板之间应加防振垫B、室内机的指示灯故障显示分析故障内容故障显示简要分析排除方法通讯故障双色灯红灯闪亮1次,停2秒通讯线未接如开路、断路或错接氧化主板或模板损坏,屏蔽网线与地连接检查通讯线的好坏和接线方法,更换控制板水泵故障双色灯的红灯闪亮2次,停2秒水泵本身故障或吸入口堵塞,线路断、无控制电压,排水管倾斜坡度不够液位检测坏检查水泵和电源及排水管坡度液位室内传感器故障双色灯的红灯闪亮3次,停2秒传感器松脱开路,接触不良、无传感电源.检查传感器和控制电压室内盘管出口温度传感器故障双色灯的红灯闪亮4次,停2秒传感器损坏,脱离固定套测温超范围或检测不到温度差.检查传感器和被测温度范围室内盘管入口温度传感器故障双色灯的红灯闪亮5次,停2秒传感器坏、脱离固定套或检测温度超范围检查传感器和被测温度范围室内盘管中点温度传感器故障双色灯的红灯闪亮6次,停2秒传感器坏、脱离固定套或检测温度超范围检查传感器和被测温度范围
2、挂壁式A、对室内机的指示灯故障显示故障内容故障显示简要分析排除方法通讯故障定时指示灯闪亮1次,停2秒连接端氧化、开路和通讯板无电源提供,接线有误或对地检查电源和接线方法,确认线控器好坏风机故障定时指示灯闪亮2次,停2秒风机本身故障,电容坏,叶轮内有异物卡住,连线断检查风机、风叶、电容和连接线室温传感器故障定时指示灯闪亮3次,停2秒传感器松脱、短路、开路、接触不良无传感器电源检查传感器和控制电压室内盘管出口温度传感器故障定时指示灯闪亮4次,停2秒传感器__不到位,超出测温范围确认传感器好坏,检测盘管进出口温度差室内盘管入口温度传感器故障定时指示灯闪亮5次,停2秒超出测温范围,传感器坏、插接有误,板坏确认传感器好坏和__位置,检查有无测量电压室内盘管中口温度传感器故障定时指示灯闪亮6次,停2秒超出测温范围,传感器坏、插接有误,板坏确认传感器好坏和__位置检查有无测量电压B、对室外机的故障显示故障内容故障显示简要分析排除方法室外机压缩机排气温度过高运行指示灯闪亮1次,停2秒缺氟,膨胀阀开度不够,系统有空气或堵塞现象,少油,室内功率过小,卸荷不好加氟,检查膨胀阀和系统是否正常缺氟换向阀故障运行指示灯闪亮2次,停2秒传感器__有误、换向阀没换向或缺氟,漏检查传感器线圈是否松脱、坏和系统压力是否正常室外机交流输入电流过大运行指示灯闪亮3次,停2秒电压不平衡波动大,模块取样异常,压机功率过大测量电网电压,确认功率过大的原因室外机交流输入电流采样异常运行指示灯闪亮4次,停2秒电源不稳,波动大,压机阻值异常,系统压力高检测电源是否超出正常范围和压机阻值,更换线控板室外机直流母线电压异常运行指示灯闪亮5次,停2秒电压超出规定范围,取样不准或线路板坏,压机工作异常测量电压和压缩机,更换线路板室内机总功率过大运行指示灯闪亮6次,停2秒JP
1、JP2跳线功率过小,或室内机总功率过大按室内机功率跳线室外机传感器故障运行指示灯闪亮7次,停2秒传感器自身故障,或松脱,插件不良,超测温范围,无传感电压检查传感器和控制电压室外机变频器模块保护故障运行指示灯闪亮8次,停2秒电压不稳,接线有误,模块故障检查电压和压机阻值,接线方法
3、柜机A、室内机控制板故障分析故障内容故障显示简要分析排除方法通讯故障F1线路连接有误,接触不良,无通信电源,对地检查通信线连接方式和屏蔽网线模块故障F2电源波动范围超差,压机绕阻故障,取样异常检查电源压机阻值和接线方法室内温度传感器故障F3传感器坏,接线开路,断路、无传感电源确认传感器的好坏和控制电压室内盘管出口温度传感器故障F4传感器坏,偏离固定套,检测不到温度差检查传感器及__位置室内盘管入口温度传感器故障F5传感器坏,偏离固定套,或超出测温范围检查传感器及__位置室内盘管中点温度传感器故障F6传感器坏,偏离固定套,或超出测温范围检查传感器及__位置B、室外机的故障显示故障内容故障显示简要分析排除方法室外机变频器模块保护故障E1电源不稳,压机绕组故障,接线有误测量电压,检查绕组值和接线方法室外机交流输入电流过大E2模块取样异常或功率匹配过大电源不稳,压机故障检查模块和跳线方法,测量电压和压机阻值室外机压缩机排气温度过高E3检查压机,冷凝器通风状况真空度不够或有堵塞现象,系统缺氟室内功率太小,卸荷不好,少油改善压机和冷凝器通风条件检查系统和跳线方法室外机传感器故障E4传感器脱离固定套,插接不良,无传感电压检查传感器的好坏及__位置和电压缺氟或换向阀故障E5电磁阀线圈松脱有开路现象,室内外传感器测温异常,系统缺氟,漏查换向阀线圈和传感器__位置,检漏室内机总功率过大E6控制板JP
1、JP2跳线功率过小或室内机总功率过大按室内机匹配跳线室外机直流母线电压异常E7电源波动、取样不准或线路板坏、压机异常检测电压和线路板及压机工作状况室外机交流输入电流采样异常E8压缩机是否启动或故障电源电压是否在正常值,压机运行不稳检查电压和压机是否正常
九、电动机绕阻的正确判断
1、风机电机绕阻的判断用万用表欧母X1档或数字万用表欧母档测量并记录,AB的阻值加AC的阻值等于BC
2、压缩机,电动机绕阻的判断Y形接法绕阻测量,用万用表欧母X1档分别测量A
0、B
0、C0其阻值应相等△形接法绕阻测量用万用表欧母X1档分别测量AB、BC、AC阻值应相等
3、绝缘值的测量以上阻值判断后需进行绝缘检测,其方法如将万用表换成欧母X10K档表笔分别接A和地金属外壳测量其阻值应大于2兆欧以上或无穷大注有线圈阻值的可依阻值参数为依据
十、CMV
145、CMV290跳线方法及功率搭配说明室外机调试板故障说明显示E12和室内线控板显示E08故障表示室内机总功率过大,造成故障的原因是室内机风机盘管功率与线路板JP
1、JP2配置不当造成其配置最大室内机总功率总和≤
6.5P单机配置根据风机盘管应选择功率,其配置方法如下风机盘管型号与功率对应表匹数HP机型1CMV-25GCMV-25P
1.5CMV-32GCMV-35GCMV-32PCMV-36P2CMV-46LCMV-51LCMV-61GCMV-46PCMV-51GCMV-61P3CMV-70PCMV-75Q
十一、大型制冷工程的电源配置大型制冷工程中其制冷设备多而集中,若不进行电源配置会造成线路压降大,工作电流高三相电力不平衡变频器取样不稳而显示E01故障停机重则因线路超载而发生事故,实行电源分路控制即可保持三相电力平衡,又可方便维修不会因单台机故障而造成大__设备停用,望在多台机接线中加以注意现以图解形式说明
十二、CMV__注意事项设备管路连接CMV管路系统采用一根主管出来再分成数根分管连接末端设备的方式,其__方法是否正确对系统的运行有较大影响,下面列出典型__方式,以供参考1)室内外机净落差少于5ma末端设备之间制冷能力相差较小时,__如下b末端设备之间制冷能力相差较大时,__如下2)室内、外机落差大于5m时,a室外机在上,末端设备在下时b室外机在下,末端设备在上时注
(1)当室内外机落差较大时,气管每隔6m~7m必须做一个回油弯;
(2)分配器一般放在室外机等高的位置3)设备冷媒追加量以室外机与最远距离末端设备统计,每米可加约125g如下按L+L4总长计,每米追加约125g4)设备管路连接后试压对于CMV管路连接,一般按下列步骤操作a准备好相关规格铜管,并用氮气__吹洗干净,(氮气压力>
0.6MPa)确保管路内无污物;b管路焊接时,管内应加
0.02~
0.05MPa氮气保护;c管路焊接完后,检查整个系统管路,确保无漏焊或虚焊,管路无明显变形并用氮气对系统管路进行吹除、连接d系统试压具体为利用氮气将压力增加为
2.4~
3.0Mpa(绝对压力)并保压24小时,其间压力下降值约在
0.03MPa左右e抽真空试验具体为利用真空泵将系统内压力抽到130Pa(绝对压力);停止一段时间待系统平衡后再抽空10分钟,并保压24h,其间压力上升不能高于20pa(绝对压力);f系统管路试压完毕,用保温管和扎带对管路进行保温处理保温材料厚度不小于8毫米g)确保整个管路保温处理后冷煤管和回气管无外露现象-30-。