文本内容:
1施工准备
1.1材料及主要机具普325#水泥,要求有出场合格证,并按规定做复试中砂含泥量不大于5%耐水腻子要求有出场合格证及各种技术资料搅拌桶、刮板、开刀、粉线包、马凳等
1.2作业条件墙体清理干净,凸出部分剔凿平整,把穿墙螺栓孔及穿墙管洞、电盒口、剔凿部分堵好抹平隔墙安装完毕,验收合格办理各种签认手续2施工要点踢脚线高度从+5线下反--mm,与墙面平墙与地面交界处要收干净3施工工艺
3.1工艺流程墙面堵洞、修补、清理一弹线一找阴阳角一大面积刮耐水腻子一打磨清理一面层腻子把墙体的洞口堵好,留出lOnmi抹灰量,抹灰找平,最后把墙面清理干净隔墙板、保温板的接缝处的玻纤布粘贴齐全牢固弹线用粉线包在阴角处弹线水平线和垂直线,根据弹出的控制线先把阴阳角大致找方正,再找大面,这头遍腻子用水泥浆找,水泥腻子刮完后,4个小时用喷雾器喷水养护两天待含水率不大于60%时上耐水腻子程序和胳水泥腻子一样,但不喷水耐水腻子刮两遍,要求阴阳角方正,大面平整最后再刮一遍耐水腻子膏状面层,在阴角部用锯条划出宽、浅1mm的线槽,先做样板间,验收合格后再开始施工4质量标准
4.1保证项目
4.
1.1所有材料要综合规定,并出具合格证及检测报告;
4.
1.2不得开裂、起皮、掉粉
4.2基本项目:
1.
2.1阴阳角方正,表面平整、颜色一致;
4.
2.2表面光洁、不得有刮痕;
5.
2.3盒口方正、干净
6.3允许偏差表面平整度不大于2nm1,垂直度不大于3nmi,阴阳角方正不大于2nlm5成品保护
6.1刮腻子不得踩压暖气片及各种管道
7.2刮腻子时要对各种设备及地面进行覆盖保护,不得污染
5.3门窗框要用不干胶条粘贴,防止污染
5.4使用的马凳不得碰撞墙、门等6应注意的质量问题
5.1墙面不干净,腻子开裂;
6.2管道后漏刮,不平整;
7.3阴阳角不方正,没有弹线找规矩;
8.4踢脚线不直,踢脚与墙面交接处不之,不顺
6.5表面不光滑,最后收活不好7注意事项
6.1墙面太干燥时,要提前浇水湿润;
7.2耐水腻子分两种,袋装的粉状腻子,用水调制刮在底层,桶装膏状直接刮,用在面层
7.3踢脚线用水泥浆刮,内掺界面剂,配比为界面剂水泥二12(重量比)8安全技术措施
8.1刮腻子用的马凳要牢固,脚手板要绑牢,宽度不少于60cm
8.2靠近窗口的部分,如窗扇没有安装上要挂的安全带,安全带要系在绑好的脚手板上
8.3室内的各种材料及垃圾均不得从窗口向外扔,剩料及垃圾由电梯运下,防在指定位置
8.4酒后不得作业。