还剩9页未读,继续阅读
本资源只提供10页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
文本内容:
中华人民共和国化学工业部部标准脱脂工程施工及验收规范HGJ202—82主编部门兰州化学工业公司建设公司批准部门化学工业部实行日期一九八三年一月一日化学工业部文件82化基字第901号“关于颁发《脱脂工程施工及验收规范》的通知”由兰州化学工业公司建设公司负责修订的《脱脂工程施工及验收规范》已会审定稿,现予以批准,自一九八三年一月一日起实行编号为HGJ202—82在实行过程中要注意积累资料,有什么问题,望随时函告部基建局,以便汇总再作修订本规范由部基建局负责管理和解释一九八二年八月四日修订说明《脱脂施工及验收技术规程》炼化建002—74自一九七四年颁发试行以来,发挥了应有的作用由于脱脂技术的不断发展,脱脂经验的不断丰富,部指定兰州化学工业公司建设公司对该规程试行本进行了全面修订,经过调研、试验、召开专业讨论会,最后经会议审查定稿并正式定为《脱脂工程施工及验收规范》HGJ202—82在修订过程中,广泛征得化工设计院、施工企业及生产、科研单位的意见,同时得到机械、冶金、石油等部,四川、上海、武汉等省、市有关单位的支持,于此表示感谢本规范由化学工业部基本建设局负责管理和解释,希各单位在执行过程中,将发现的问题随时函告我局,以利下次修订化学工业部基本建设局一九八二年七月附表二碱性脱脂配方及使用条件项次配方、重量%适用范围氢氧化钠
0.5~1碳酸钠5—10适用于•般钢铁件1硅酸钠3~4水余里氢氧化钠1〜2碳酸钠5〜8适用于•般钢铁件2硅酸钠3〜4水余量氢氧化钠
0.5〜
1.5磷酸钠3〜7适用于一般铜及铜合金件3碳酸钠
8.5硅酸钠1〜2水余量磷酸钠5〜8磷酸二氢钠2〜3碱性较弱,有除油能力,对金4硅酸钠5〜6烷基苯磺酸钠
0.5〜1属腐蚀性较低,适用于钢铁件水余量和铝合金件附表三非离子型金属清洗剂“664”配方及使用条件配方、重量%性能与用途清洗条件脂肪醇聚氧乙烯醛12不易燃、无毒性、溶液稳定,对于配制成2〜3%(重量)的水溶椰子油烷基醇酰胺12材质为钢铁、铝的精密件较适用,液,加热至70±5℃,脱脂件浸聚氧乙烯辛烷基酚醛10如需清洗铜制件,可适量添加
0.2%入溶液洗涤5〜10分钟,取出三乙醇胺油酸皂50的苯骈三氮喋,清洗后会产生发粘后用热水漂洗干净,然后干燥水20现象,必须用热水将脱脂件反复清洗干净附表四W4L W25气相透锈纸的用途牌号性能与用途对钢、紫钢、镀青铜、磷青铜、铝铁青铜、铝及其合金鸨钻合金有良好的防锈效果,W41对铸铁也有一定的防锈效果W25对钢、镀青铜、锡青铜、巴氏合金有良好的防锈效果注W
41、W25气相防锈纸包装的零部件,经清洗干净干燥,再用塑料袋密封,防锈期可达三年以上附表五BF—
7、CF—4气相防锈塑料薄膜的用途牌号性能与用途BF-7对钢、铝及其合金有良好的防锈能力对钢、铝及其合金有良好的防锈能力对铜及CF-4镀锌、镀镉钝化件有适应性第一章总则第二章一般规定第三章设备脱脂第四章管子、管件和阀门的脱脂第五章检验第六章安全技术附表一常用脱脂剂的部分特性数据附表二碱性脱脂液配方及使用条件附表三非离子型金属清洗剂“664”配方及使用条件附表四W
41、W25气相防锈纸的用途附表五BF—
7、CF—4气相防锈塑料薄膜的用途第一章总则第L
0.1条本规范适用于化工工程建设中的忌油设备、管子、管件、阀门等的脱脂第
1.
0.2条设备、管子、管件、阀门等,必须根据设计文件或下列规定,按本规范进行脱脂:
一、输送、贮存的物料遇油脂等有机物可能发生燃烧或爆作者;
二、油脂等有机物能与输送、贮存的物料相混合并能改变物料的使用特性者;
三、油脂等有机物对触媒的活性有影响者;
四、油脂等有机物对产品纯度有影响者;
五、由于酸洗需进行脱脂处理者第L
0.3条设计对脱脂另有要求者,应按设计文件的规定执行第L
0.4条脱脂剂的贮运设施,应按《炼油化工企业设计防火规定》执行第二章一般规定第条设备、管子、管件、阀门等的脱脂应在系统气密性试验前完成第条脱脂施工前,施工部门必须编制专用的脱脂操作规程参加脱脂施工的人员,必须根据本规范及编制的专用操作规程进行施工第条有明显油迹和污垢的零部件,在脱脂前可先用煤油等溶剂或其它方法清除油迹和污垢,然后再用脱脂剂脱脂在整个过程中均须采取相应的安全措施第条脱脂剂应按设计要求选用如设计无规定时,施工部门应根据脱脂件的材质、结构、污染程度、现场条件、生产介质及其因沾染油脂而造成的危险或危害程度,选择相应的脱脂剂和脱脂方法第条脱脂剂可按表
2.
0.5选用(常用脱脂剂的部分特性数据见附表一)表常用脱脂剂脱脂剂名称适用范围附注工业二氯乙烷金属件能水解生成微量盐酸()C2H4C12工业四氯化碳黑色金属、铜和非在水和金属共同存在时能发生水解生成微量盐(CC14)金属件酸,与某些灼热轻金属能起强烈的分解反应,甚至爆炸工业三氯乙烯金属件含稳定剂的纯三氯乙烯对一般金属无腐蚀()产品,必须含稳定剂C2HC13工业酒精(C2H5OH)脱脂要求不高的设脱脂能力较弱(浓度不低于
95.6%)备和零部件98%的浓硝酸浓硝酸装置的耐酸强氧化剂,能溶解或腐蚀某些金属管件和瓷环碱性脱脂液(配方及形状简单、易清洗不宜用于精密件、形状复杂、多孔深孔部件、卸使用条件见附表二)的零部件和管路件接件、具有表面转化层的金属组合制非离子型金属清洗剂宜用于精密件以及油脂污染不太严重的制形状简单、易清洗的“664”(配方及使钢铁、铝等制件件用条件见附表三)第条脱脂剂或用于配制脱脂剂的化学制品必须具有合格证脱脂剂在使用前应按技术条件对其外观、不挥发物、水分、反应介质、油脂含量进行复验,使用过程中应作阶段性检查第条用于脱脂的有机熔剂含油量不应大于50毫克/升对于含油量较大的溶剂可用于粗脱脂,然后用清洁的溶剂进行再次脱脂含油量大于500毫克/升的溶剂必须经过再生处理,并经检验合格后,方可作为脱脂剂第条二氯乙烷、四氯化碳、三氯乙烯在一定条件下均能水解生成盐酸腐蚀金属因此,在采用这类溶剂时,脱脂件不得含有水分第条脱脂、检验及安装所用的工具、量具、仪表等必须按脱脂件的要求预先脱脂未经脱脂者,不得使用经脱脂的工具、量具、仪表等应有专用柜存放,并由专人保管工作服、鞋、手套等劳保用品必须干净无油第
2.
0.10条脱脂应在室外或有通风装置的室内、器内进行脱脂现场要求通风良好,不受雨水、尘土等的侵染脱脂剂不应受阳光直接照射第2・
0.11条脱脂件应在脱脂后及时将其内部的液态脱脂剂排放尽,严禁用蒸发干燥的方法清除残液第条清除脱脂件表面上的溶剂,直至无残液和无气味为止其方法
一、可用清洁无油干燥的空气或氮气吹净;
二、当用二氯乙烷或酒精等易燃溶剂脱脂时,只许用纯度等于或大于95%(按容积计)的氮气吹净或在空气流通处晾干;
三、对于构造不复杂、体积较小的脱脂件,可在大气中自然通风24小时以上;
四、为缩短吹净时间,可用预热至50—60C的空气或氮气进行吹除;
五、可用干净脱脂棉外敷织物且缚于长杆上的沾取包,清除器底的渣屑残液第
2.
0.13条为加速清除残存熔剂,在脱脂件允许时可用清洁无油的蒸汽吹除第
2.
0.14条采用擦拭法脱脂时,不宜使用棉纱,应用纤维不易脱落的布、丝绸、玻璃纤维织物等脱脂后必须仔细检查脱脂件表面,严禁有机织物的纤维落入、附着在脱脂件表面上第条设备、管子,管件、阀门等在脱脂后,必须经专职检查人员检查和有关人员签证人为合格,方可进行下道工序第
2.
0.16条脱脂件经检查合格,应由专人负责封闭,并加标志零件应用干净的白布包好,妥善存放,防止脏物和杂物沾染或侵入把脱脂合格的与不合格的或未脱脂的零部件必须隔离存放,严禁相混第2・
0.17条要求防锈的脱脂件经脱脂防锈处理后,可采取充氮封存或用气相防锈纸、气相防锈塑料薄膜密封等措施予以保护用于封存的氮气不得含油,其纯度必须等于或大于95%(按容积计),露点应低于一40℃部分气相防锈纸、气相防锈塑料薄膜的牌号、用途见附表四和附表五第
2.
0.18条脱腊后的设备、管道,不得使用含油的介质进行压力试验及吹扫第2・
0.19条脱脂施工中,脱脂人员应认真执行工序交接、交接班和原始记录制度第三章设备脱脂第条静止设备应在强度试验合格后方准进行脱脂第条设计文件规定由制造厂脱脂的设备,必须具有制造厂的脱脂合格证件具有制造厂脱脂合格证且封闭、保管良好的设备在安装时可不再进行脱脂但在安装前应经有关人员进行仔细检查并确认若发现污物或被油脂污染,则应重新进行脱脂.对需重新进行脱脂的设备必须编制脱脂方案,并经主管技术部门批准第
3.
0.3条对结构复杂和有死角的部件或设备,要采取必必要措施,使脱脂剂能均匀散布到全部表面,并在脱脂后能将脱脂剂排放尽第
3.
0.4条脱脂件表面必须经脱脂检查合格后,方准涂以规定的润滑、防蚀及密封剂第条设备在脱脂过程中的拆卸、吊放、吹除等各项操作,必须遵守设备安装、拆卸的有关规定第
3.
0.6条静止设备的脱脂可按接触介质、结构和油污程度分别采用下列方法
一、灌浸法容积不大的设备,可采用灌注溶剂浸泡的方法脱脂,此时应旋转或反复倾斜设备,使所有需脱脂的表面能均匀地与溶剂接触浸泡时间视污染程度而定,一般为1小时;
二、擦试法较大的金属容器,当油污轻微时,可用清洁织物浸蘸脱脂剂擦洗;
三、喷淋法大容器的内表面脱脂,可采用喷头喷淋脱脂剂的方法喷头应能上下升降,使溶剂能均匀地喷淋到容器的全部需脱脂表面;
四、循环法管式换热器的脱脂,可来用循环溶剂的方法进行但必须使溶剂能循环到需脱脂的全部表面循环时间一般不得少于30分钟;
五、槽浸法允许拆卸的零部件,可直接浸入溶剂槽内浸泡浸泡时间视污染程度而定,一般为1小时第
3.
0.7条传动设备凡与忌油介质接触或可能接触的部件(如润滑和密封部分等),在投产前必须进行脱脂,但应按有关规程完成机体安装、找正、调整各部间隙等工作,然后解体脱脂第
3.0・8条传动设备可拆卸的零部件如压缩机或泵的缸盖、活塞组件、阀件、密封件、转子、隔板、蜗壳、螺栓、垫片等,可先用煤油清洗,然后放入溶剂槽内浸泡,直至合格第
3.0・9条传动设备不能拆卸或浸入溶剂槽内有困难的大部件,如压缩机和泵的气缸、壳体等,可用擦拭法脱脂第条经脱脂合格的传动设备零部件,应保持干净并尽快组装设备组装后,如不能及时投入生产,应用脱脂合格的盲板将管道隔开并封闭,采取防锈保护措施,以免污染和锈蚀第四章管子、管件和阀门的脱脂第
4.
0.1条已铺设的管道脱脂,可拆卸成管段或用循环脱脂的方法进行不能拆卸或循环脱脂有困难的管道,应在铺设前进行脱脂,但必须保持不被污染第条有明显锈蚀的管子应经喷砂或用其它方法清除铁锈,再用脱脂剂脱脂第条管子内表面脱脂,可在管内注入溶剂,管端用木堵或其它方法封闭将管子放平浸泡1〜
1.5小时,每隔15分钟转动一次,逐次转到应浸泡的部位上每次转动都要使管子滚动几个整圈,使管子的整个内表面都能均匀地受到溶剂浸泡和多次洗涤管子每长1米,其内表面脱脂所需的溶剂量,一般可按表
4.
0.3确定表管子内表面脱脂用量管子内径,毫米15202532405070熔剂量,升溶
0.
150.
200.
300.
400.
500.
600.70剂浸没圆弧251°205°200°179°164°143°116°管子内径,毫米80100125150200250300熔剂量,升溶
0.
801.
001.
251.
502.
002.
503.00剂浸没圆弧110°102°93°87°79°73°68°第条大口径管子可用擦拭法擦洗,小口径管子可整根放在溶剂内浸泡1—
1.5小时第条预制好的管段也可在连接后用循环溶剂的方法进行脱脂但必须使溶剂能循环到需脱脂的全部内表面,密封面必须单独脱脂,溶剂循环的时间一般不得少于30分钟第条管子外表面的脱脂可用擦拭法擦洗第
4.
0.7条阀门脱脂前应研磨试压合格,然后拆成零件清除铁锈等杂物,浸入溶剂内浸泡1—
1.5小时螺栓与金属垫片用同样方法脱脂不便浸泡的阀门壳体,可用擦拭法进行第条非金属垫片的脱脂,应使用四氯化碳溶剂垫片侵入溶剂内
1.5—2小时,然后取出悬挂在空气流通处或通风装置内逐个分开吹干,直至无溶剂气味为止第条外包金属层的垫片或需浸涂料的垫片脱脂,应在包敷金属层和浸涂前进行第
4.
0.10条接触氧、浓硝酸等强氧化性介质的石棉填料,可在300℃左右的温度下灼烧2〜3分钟(不得用有烟的火焰),然后浸渍规定的涂料对于已浸渍涂料的石棉填料成品,应具有适用范围的合格证,否则必须经化验合格后,方可使用第
4.
0.11条工作介质为浓硝酸的阀门、管件、瓷环等可用98%的浓硝酸洗涤或浸泡,继用清水冲洗,然后以蒸汽吹洗,直至冷凝液无酸度为止铝及铝合金件在浓硝酸洗涤浸泡后要及时将脱脂件上的酸洗净,以防止稀酸腐蚀第五章检验第条设备、管子、管件、阀门脱脂后应经检验鉴定检验标准应根据脱脂件在生产中的不同作用和因沾染油脂而造成的危险或危害程度,按本规范第
5.
0.2条至第
5.
0.5条执行第
5.
0.2条直接或可能与氧、富氧、浓硝酸等强氧化性介质接触的设备、管子、管件、阀门等,可采用下述任意一种方法进行检验
一、用波长3200—3800埃的紫外光检查脱脂件表面,无油脂萤光为合格;
二、用清洁干燥的白色滤纸擦抹脱脂件表面,纸上无油脂痕迹为合格;
三、用无油蒸汽吹洗脱脂件,取其冷凝液,放入一小粒(直径1毫米以下)纯樟脑,以樟脑料不停旋转为合格;
四、不能用上述方法检验的脱脂件,可取样检查脱脂后的溶剂油脂含量不得超过350毫克/升为合格第条用浓硝酸清洗的设备和管道应分析其酸中所含有机物总量,以不超过
①03%为合格第条用溶剂脱脂的脱脂件必须将残存溶剂彻底吹除直至无溶剂气味为止用碱液脱脂者必须用无油清水冲洗洁净至中性,然后干燥用蒸汽吹除者,应及时将脱脂件干燥用于冲洗奥氏体不锈钢的无油水,其氯离子含量不得大于25ppmo第条设计有规定检验标准者,应按设计规定的标准检验第六章安全技术第
6.
0.1条脱脂现场周围应清除一切易燃易爆物及其它杂物,划分脱脂专责区域,无关人员不得进入严禁烟火,消除一切可能发生火花的来源,并设置“严禁烟火!”、“有毒物品!”等标示牌脱脂现场必须具有必要的防火、防毒设施,经常检查使之处于良好的备用状态第条二氯乙烷、四氯化碳、三氯乙烯等溶剂是易挥发的有毒液体,能通过呼吸道中毒,侵害人体内脏和神经系统;二氯乙烷、四氯化碳还能通过完好的皮肤吸收中毒脱脂工作应在室外或有通风装置的室内进行工作时要加强个人防护,应穿戴工作服、口罩、防护眼镜、胶皮手套、围裙及长筒套靴,必要时应戴防毒面具脱脂场所严禁吸烟或进食,并应定期检查脱脂工作地点空气中的有害物质含量,其浓度不应超过表
6.
0.2的规定表脱脂工作地点空气中的有害物质的最高容许浓度名称最高容许浓度,毫克/立方米备注二氯乙烷25能通过皮肤呼吸道吸收中毒四氯化碳25能通过皮肤呼吸道吸收中毒三氯乙烯30易灼伤皮肤苛性碱(换算成NaOH)
0.5易灼伤皮肤浓硝酸(换算成NO2)5熔剂汽油350第条硝酸能侵害皮肤粘膜用浓硝酸脱脂的人员应穿毛料、丝绸或胶质工作服,戴耐酸胶皮手套、防护眼镜和夹有小苏打的双层口罩,必要时应戴防毒面具第条苛性碱能腐蚀皮肤粘膜用碱液脱脂时,操作人员应穿戴胶质工作服、围裙、手套、长筒套靴和防护眼镜第条用浓硝酸或碱液脱脂的现场应安装临时冲洗水管当酸或碱液滴于皮肤时,应立即用清水冲洗净,不得搓揉第条三氯乙烯、二氯乙烷和酒精均属甲类火灾危险性物质,与空气混合接触火花即引起燃烧爆炸,与浓硝酸、氧化剂接触能引起自燃在使用和贮存时要严禁烟火,并与强酸和氧化剂等隔离第
6.
0.7条酒精不得和二氯乙烷等本规范所列的其它脱脂剂共同贮存和同时使用第条用二氯乙烷或酒精等易燃溶剂脱脂后,严禁用氧气或空气强力吹除的方法干燥残存溶剂第条四氯化碳与火焰或灼热轻金属如钾、镁、钠、铝等及其它化学物品如电石、乙烯、二硫化碳等接触,能引起强烈分解,甚至发生爆炸因此在贮存和使用四氯化碳时,严禁烟火,不得与这些物质接触第
6.0・10条三氯乙烯与火焰接触可生成光气,能与固体苛性钠或苛性钾反应引起爆炸,与水或其它杂质接触容易分解因此在贮存和使用三氯乙烯时,严禁烟火,且不得与这些物质接触第
6.
0.11条浓硝酸是一种强氧化剂,与有机物、松节油、水、有机织物接触即自燃,燃烧时产生过氧化氮等有毒气体贮存时必须将容器封严,防止受潮、漏损,且应专设库房,并与有机物、可燃物、酸类及其它氧化物隔离第
6.
0.12条脱脂剂应分别贮于密闭的玻璃瓶或铁桶内,避光保存于通风良好的干燥、凉爽仓库中脱脂剂不得与强酸或强碱接触第条应防止脱脂剂溅出和溢到地面上溢出的溶剂应立即用木屑、砂子等将其吸干并和脱脂用过的织物一起收集在专用的密闭金属容器内,但对溢出的酸,碱应立即用大量的水冲洗至中性第
6.0・14条把溶剂从一个容器倒入另一个容器时应在露天,且穿戴好防毒面具等防护用具后,方可进行第6・
0.15条严禁不同的溶剂混合和不按适用范围使用第6・0・16条脱脂残液及污物的排放,必须按《工业“三废”排放试行标准》GBJ4-73的规定执行第
6.
0.17条脱脂现场必须加强管理和保卫,以免发生意外事故附表一常用脱脂剂的部分特性数据二氯乙烷四氯化碳三氯乙烯酒精CIH5OH名称()()CC14C2HC12()C2H4C12分子量
98.
97153.
84131.
4046.07沸点,℃(760毫米汞柱)
83.
776.
7587.
378.4比重20/4℃
1.
2551.
5941.
4770.789蒸汽比重
3.
55.
34.
541.613(与同温同压空气相比)闪点,℃2114自燃点,℃378510-568爆炸极限(空气中)20℃11℃-39℃熔点,℃-
35.3-
22.9-73-
114.5蒸发速度(以乙醛为100)28蒸发潜热,卡/克
57.2比热,卡/克℃
0.225(20℃液体)。